valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
All Rights Reserved. 5 TP 400-4155-01-LW-S Handles and Controls Group - 1060, 1170, 1280 & 1390 Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. Linkage adjustment for traction and auger drive with power boost: with drive levers engaged, the bottom end of lower rods (Ref. 40 & 66) should be flush with bottom of springs (Ref. 39 & 68). To engine ground Shift rod assembly (Ref. 71) must pivot freely on pivot blocks (Ref. 21). Torque to 19 - 29 ft-lbs. Mount clutch cable to cable support, see Engine & Frame. To engine plug To spout motor To headlight See Auger Housing and Chute Group - 38" The holes in the frame for Ref. 51 are slotted so the gear support (Ref. 45) can be positioned to ensure the inside surface of the gear support is tight against the hub of the front gear (Ref. 50). Mount bushings (Ref. 78) with flange on inside of brackets, 3 places. Slot towards rear of unit. 10 14 13 1 2 4 78 5 6 3 7 21 12 12 9 15 16 17 18 19 25 57 8 20 23 24 35 36 37 38 39 40 26 34 4 66 63 38 37 69 74 75 74 59 76 4 82 80 81 79 96 4 4 5 77 4 70 71 72 59 65 65 59 68 36 67 64 22 73 56 58 61 27 60 59 11 34 33 29 30 31 32 83 42 41 44 45 43 46 53 50 48 49 52 46 51 47 43 43 55 54 48 43 28 12 62 84 986724 The above parts group applies to the following Mfg. Nos.: © Copyright 2 0 0 5 Simplicity Manufacturing, Inc. All Rights Reserved. 6 1694590 - 1060E 1694591 - 1170E 1694592 - 1280E 1694593 - 1390E 1694598 - 1060M 1694599 - 1170M 1694600 - 1280M 1694601 - 1390M TP 400-4155-01-LW-S Handles and Controls Group - 1060, 1170, 1280 & 1390 Models PART NO. REF NO DESCRIPTION QTY. 44 1715658 1 ROD, Chute Control, 27" Long (9560, 1060, 1170 & 1280 Models Only) 45 1718793 1 SUPPORT, Gear (9560, 1060, 1170 & 1280 Models Only) 46 1718593 2 GEAR, Powered Metal (9560, 1060, 1170 & 1280 Models Only) 47 1918452 1 PIN, Cotter 1/8 x 1 (9560, 1060, 1170 & 1280 Models Only) 48 2816168 2 PIN, Spring 1/8 x 3/4 (9560, 1060, 1170 & 1280 Models Only) 49 1725283 1 ROD, Chute Worm, 18 Long (9560, 1060, 1170 & 1280 Models Only) 50 1668186 1 WORM, Chute, L.H. (9560, 1060, 1170 & 1280 Models Only) 51 1960252 2 CARRIAGE BOLT, 1/4-20 x 5/8 G5 (9560, 1060, 1170 & 1280 Models Only) 52 1960294 2 NUT, Hex Flange Whiz Lock, 1/4-20 Small (9560, 1060, 1170 & 1280 Models Only) 53 1611911 1 SUPPORT, Worm (9560, 1060, 1170 & 1280 Models Only) 54 1931333 1 CARRIAGE BOLT, 5/16-18 x 3/4 G5 (9560, 1060, 1170 & 1280 Models Only) 55 1960684 1 NUT, Hex KEPS Conical Washer, 5/16-18 (9560, 1060, 1170 & 1280 Models Only) 56 1723967 1 SWITCH, Hand Warmer (1280 & 1390 Models Only) 57 1923341 1 CAPSCREW, Hex Head, 1/4-20 x 3/4 G5 (1280 & 1390 Models Only) 58 1724037 1 RESISTOR BLOCK, Male Terminal (1280 & 1390 Models Only) 59 1960685 4 NUT, Hex KEPS, 1/4-20 Conical Washer 60 2172434 1 CLIP, Wire (Spout Rotator Models Only) 61 1725439 1 HARNESS, Wiring (Handwarmer Models Only) 61 1725409 1 HARNESS, Wiring (Handwarmer & Spout Rotator Models Only) 62 2825094 3 TIE, Self Locking 7-5/16 (1280 & 1390 Models Only) 63 1722460 1 PIN, Quick 64 1666255 1 ROD, Lower Shift 15-21/64 Long 65 1931317 2 CARRIAGE BOLT, 1/4-20 x 3/4 G5 66 1702004 1 ROD, Lower Clutch 67 1726304 1 ROD, Upper Shift 11-3/8 Long 68 1701996 1 SPRING, Extension 4-3/4 Long 69 1702485 1 ROD, Upper Clutch 70 1713844 1 KNOB, Hole 71 1714120 1 ROD & CLEVIS ASSEMBLY, Shift 72 1960705 1 CAPSCREW, Hex Flange Whiz Lock 1/4-20 x 2-1/4 73 1668681 1 WASHER, Curved 74 1668524 2 BLOCK, Pivot, Powdered Metal 75 1924361 1 WASHER, 1/2 76 1703043 1 ROD & ARM ASSEMBLY, Pivot 77 1960074 1 CLIP, Hair Pin 78 1702663 1 ROD, Clutch 5-11/32 Long 79 1933689 1 CAPSCREW, Hex Flange Whiz Lock 5/16-18 x 1-1/2 80 1919326 1 WASHER, 5/16 81 1702662 1 LEVER, Clutch 82 1702552 1 SPACER, 21/64 ID x 3/4 OD x 53/64, Powdered Metal 83 1960518 2 NUT, Push for 1/4 Diameter Thread 84 1701011 1 TIE, Self Locking, 15" (Spout Rotator Models Only) Footnotes The above parts group applies to the following Mfg. Nos.: 1694590 - 1060E 1694600 - 1280M 1694591 - 1170E 1694601 - 1390M 1694592 - 1280E 1694593 - 1390E 1694598 - 1060M 1694599 - 1170M © Copyright2005 Simplicity Manufacturing, Inc. All Rights Reserved. 7 TP 400-4155-01-LW-S Handles and Controls Group - 9560 Models NOTE: Unless noted otherwise, use the standard hardware torque specification chart. The holes in the frame for Ref. 44 are slotted so the gear support (Ref. 42) can be positioned to ensure the inside surface of the gear support is tight against the hub of the front gear (Ref. 50). Mount bushings (Ref. 14) with flange on inside of brackets, 3 places. Slot towards rear of unit. Shift rod assembly (Ref. 61) must pivot freely on pivot blocks, (Ref. 63). Apply adhesive to secure grips. Insert shift rod (Ref. 58) into outter hole of Ref. 64. Must pivot freely on capscrew (Ref 27). Apply lubricant as required. Must slide freely in dash assembly (Ref 13). Apply lubricant as required. 43 1 2 3 9 12 13 15 16 21 11 22 7 12 39 4 5 34 36 37 38 40 54 55 57 56 56 58 64 65 63 66 62 3...
Questo manuale è adatto anche per i modelli :Sgombraneve - 1060E (1.73 mb)
Sgombraneve - 1170E (1.73 mb)
Sgombraneve - 1170M (1.73 mb)
Sgombraneve - 1280E (1.73 mb)