valutazioni - , GPA:
(
)
)
Produttore : Cub Cadet
File Size : 8.09 mb
File Nome : 467dd5c4-20fa-a5f4-5d34-8847d3d0796f.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
See Figure 8. Skid Shoe The position of the skid shoe is determined by the condition of the ground from where snow has to be removed. See Figure 8. Shift Lever The shift lever is located in the center of the handle panel and is used to determine both ground speed and direction of travel. It can be moved into any of eight positions. See Figure 8. Forward Your snow thrower has six forward (F) speeds. Position number one (1) is the slowest. Position number six (6) is the fastest. Reverse Your snow thrower has two reverse (R) speeds. R1 is the slower, while R2 is the faster of the two. IMPORTANT: Always release tractional control before changing speeds. Electric Chute-Rotation Switch The electric chute-rotation switch is located on the left side of the snow thrower dash panel. See Figure 8. To change the direction in which discharged snow is thrown, proceed as follows: • Push the toggle switch to the left to rotate the chute counterclockwise. • Push the toggle switch to the right to rotate the chute clockwise. IMPORTANT: Release the switch once the chute has completed its rotation cycle in either direction. Failure to do so can result in damage to the electric chute motor and/or its drive gear. Headlight The headlight is on whenever the engine is running. Throttle Control The throttle control is located on the engine. It regulates the speed of the engine and will shut off the engine when pushed down completely. See Figure 8. Safety Ignition Key The safety ignition key must be fully inserted in the switch before the unit will start. Remove the ignition key when the snow thrower is not in use. See Figure 8. IMPORTANT: Do NOT attempt to turn the key. Fuel Shut-off Valve The fuel shut-off valve, located under the fuel tank, controls fuel flow from the tank. Always make certain it is in the Open (vertical) position before attempting to start the engine. See Figure 8. Heated Handles Switch This switch is located on the right side of the snow thrower dash panel. To activate the heated handles, toggle the switch to the right to generate heat within the handle grips. Toggle the switch to the left to the OFF position after using the snow thrower. See Figure 8. NOTE: The heated handles grips are a compliment to, not a substitute for, proper cold weather outerwear for the operator’s hands. It is recommended that the snow thrower operator wear gloves/mittens to avoid extremities of winter while operating this equipment. SECTION 4: OPERATING YOUR SNOW THROWER Before Starting Gas And Oil Fill-up Service the engine with gasoline and oil as WARNING: Read, understand, and follow instructed in the separate engine manual packed with all instructions and warnings on the your snow thrower. Read instructions carefully. machine and in this manual before operating. 8 WARNING: Use extreme care when handling gasoline. Gasoline is extremely flammable and the vapors are explosive. Never fuel machine indoors or while the engine is hot or running. Extinguish cigarettes, cigars, pipes an other sources of ignition. • A plastic cup is provided inside the fuel fill opening on the fuel tank. Remove and discard this cup before filling up the tank. Use the separate fuel tank cap to close after fill-up. To Start Engine NOTE: If unit shows any sign of motion (drive or augers) with the clutch grips disengaged, shut engine off immediately. Readjust as instructed in the Final Adjustments in the Assembly Section. • Attach spark plug wire to spark plug. Make certain the metal loop on end of the spark plug wire (inside the boot) is fastened securely over the metal tip on the spark plug. • Make certain the fuel shutoff valve is in the OPEN (vertical position). See Figure 7. • Make certain the auger and drive control levers are in the disengaged (released) position. • Move throttle control up to FAST position. Insert ignition key into slot. See Figure 7. Be certain it snaps into place. Do not turn key. NOTE: Engine will not start unless ignition key is inserted into ignition slot in carburetor cover. Electric Starter • Determine that your house wiring is a three-wire grounded system. Ask a licensed electrician if you are not certain. • If your house wiring system is not a three-wire grounded system, do not use this electric starter under any conditions. WARNING: The electric starter is equipped with a grounded three-wire power cord and plug and is designed to operate on 120 volt AC household current. It must be used with a properly grounded three-prong receptacle at all times to avoid the possibility of electric shock. Follow all instructions carefully prior to operating the electric starter. • If your home electrical system is grounded, but a three-hole receptacle is not available, one should be installed by a licensed electrician before using the electric starter. • Remove ignition key. Do not turn key. Disconnect the spark plug wire from the spark plug to prevent • If you have a grounded three-prong receptacle, proceed as follows: • Rotate choke knob to O...