valutazioni - , GPA: ( )

Istruzioni per l'uso Bolens, Modello POULANPRO 96192001902

Produttore : Bolens
File Size : 2.61 mb
File Nome : 1f89368f-4838-41e2-8a6c-73cd4cf2c5a1.pdf

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/ impellerandallmoving partshavestopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting. Releasethe auger control lever and shut offthe engine. -Removethe clean-outtool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge the blockage. After the packed snow has been dislodged, return the clean- out toot to it's mounting clip by pushing it into the clip. • Make surethe discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting the engine. • Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute. DISCHARGE CHUTE \ TOOL MOUNTING • Squeezetraction drivecontrollevertohandletoengage the drive system. Release traction drive control lever to stop the forwardor reverse movement of the snow thrower. SPEED and DIRECTION are controlled by the drive speed control lever. Press downward on the speed control leverand move lever to desired position BEFORE engaging the traction drive control lever. Be sure leversprings back and locks into desiredposition. I is recommended that you use a slower speed until you are familiar with the operation of the snow thrower. NOTE: When both traction drive and auger control levers are engaged, the traction drive control lever will lock the auger control lever in the engaged position. This will allow you to release your right hand from the handle and adjust the discharge chute direction without interrupting the snow throwing process. DRIVE CONTROL LEVER FIG. 17 POWER STEERING OPERATION (See Fig. 18) Steeringtriggersare usedtoassistinsteeringyoursnowthrower. The triggers are located on the underside of each handle. When atrigger is squeezed, it disengages the drive wheel on that side of snowthrower and allows itto turn inthat direction. ° To turn left-squeeze left side trigger. • To turn right-squeeze right side trigger. LH TURN RH TURN TRIGGER TRIGGER FIG. 18 FIG. 16 TO ADJUST SKID PLATES (See Fig. 19) TO MOVE FORWARD AND BACKWARD (See Fig. 17) NOTE: The wrench provided in your parts bag may be usedto adjust the skid plates. SELF-PROPELLING, forward and reverse movement of the snow thrower, is controlled by the traction drive controlSkidplatesare locatedoneach sideof the auger housing lever located on the left side handle. 11 andadjust the clearance betweenthe scraper barand the OPERATION ground surface. Adjust skid plates evenly to proper heightfor current surface conditions. For removal of snow in normal conditions, such as a paved driveway or sidewalk, place skid plates in the highest position (lowest scraper clearance) to give a !/8" clearance between the scraper bar and the ground. Use a middle position if the surface to be cleared is uneven. NOTE: ttis not recommended to operate the snowthrower over gravel orrocky surfaces. Objects such asgravel,rocks or other debris, can easily be picked up and thrown bythe impeller, which can cause serious personal injury, property damage or damage to the snow thrower. , if snow thrower must be operated over gravel surface, use extra caution and be sure skid plates are adjusted to lowest (highest scraper clearance) position. 1. Shut off engine and wait for all moving parts to stop. 2. Adjustskid plates by loosening the hexnuts, then moving skid plate to desired position. Be sure both plates are adjusted evenly. Tighten securely. HIGH (LOW GROUND AUGER [ HOUSING ti // SCRAPER BAR == ._._ NITS / LOW POSITION (HIGH GROUND CLEARANCE) FIG. 19 SCRAPER BAR The scraper bar is not adjustable, but is reversible. After considerable use it may become worn. When it has worn almost to the edge of the housing, it can be reversed, providing additional service before requiring replacement. Replace a damaged or worn scraper bar. TO USE DRIFT CUTTERS (See Fig. 20) Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower. • Loosen upper adjustment nut enough to allow drift cutter to be raised to highest position and tighten nut securely. Repeat for opposite side of snow thrower. • When not using drift cutters, loosen adjustment nut, lower to storage position and tighten nut securely. AUGER HOUSING DRIFT CUTTER IT°#g# ADJUSTMENT NUT FIG. 20 BEFORE STARTING THE ENGINE CHECK ENGINE OIL LEVEL (See Fig. 21) The engine on your snow thrower has been shipped, from the factory, already filled with oi!. 1. Check engine oil with snow thrower on level ground. 2. Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw tight, wait for a few seconds, remove and read oil level. If necessary, add oil until "FULIL'mark on dipstick is reached. Do not overfill. • To change engine oil, s...