valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
MTD PRODUCTS INC. P.O. BOX 368022 CLEVELAND, OHIO 44136-9722 PRINTED IN U.S.A. FORM NO. 48898 (7/03) RULES FOR SAFE OPERATION Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. 1. This cab provides foul weather protection only. It 4. The snow cab will restrict your field of vision in does not provide protection against exhaust fumes, some directions. Use extra caution when operating collision, rollover or other accidents. your tractor with the snow cab attached. 2. Read the snow cab and vehicle owner's manuals 5. Watch out for low tree limbs or other overhead and know how to operate your vehicle before using obstructions that may not previously have inter- the snow cab attachment. fered with operation of the tractor. The extra height 3. Be sure there is adequate ventilation when using of the snow cab may cause these objects to the tractor and snow cab in confined areas. become obstacles. 6. Check the area of operation thoroughly before using the tractor. Look for this symbol to point out important safety precautions. It means--Attention!! Become alert!! Your safety is involved. UNPACKING Open carton. Remove parts and literature. Make NTENTS certain all parts and literature are removed before the carton is discarded. Lay out all parts according to the illustration below. CARTON CONTENTS 1. Base Assembly 7. Upright Tubes (2) 2. RH Adapter Bracket 8. Rope 3. LH Adapter Bracket 9. Support Rods (3) 4. Tool Bracket 10. Top Tubes (2) 5. Drawbar Bracket 11. Vinyl Canopy 6. U-Tube Parts Bag (see page 3) 7 6 10 9 8 5 2 3 11 4 1 2 A B C D E F G L M N H J KI NOT SHOWN FULL SIZE SHOWN FULL SIZE A B C D E F G L M N H J KI NOT SHOWN FULL SIZE SHOWN FULL SIZE REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A B C D E F G 1 2 4 8 2 8 2 Hex Bolt, 5/8” x 1-3/4” Carriage Bolt, 5/16 x 2" Hex Bolt, 1/4 x 1-1/2" Hex Bolt, 5/16” x 1” Shoulder Bolt Lock Washer, 5/16” Flat Washer, 5/16” H I J K L M N 4 8 1 2 4 2 2 Hex Lock Nut, 1/4” Hex Nut, 5/16” Hex Nut, 5/8” Jam Nut, 1/2” Spiral Hook Footrest Clamp Plastic Knob 3 4 TOOLS REQUIRED FOR ASSEMBLY (2) 7/16" Wrenches (2) 1/2” Wrenches (1) 3/4” Wrench (2) 15/16” Wrenches REMOVAL OF PARTS FROM TRACTOR 1. Remove any rear mounted attachments which may be installed on your tractor 2. Mark and save all removed parts. ASSEMBLING BRACKETS TO TRACTOR FAST-ATTACH TRACTORS 3. Skip to ASSEMBLING THE BASE STANDARD FRAME TRACTORS 4. Remove top four bolts from rear of tractor frame. See figure 1. 5. Attach LH and RH adapter brackets to rear of tractor frame using bolts removed in step 4. See figure 2. FIGURE 1 FIGURE 3 FIGURE 2 ASSEMBLING THE BASE 7. Assemble the drawbar bracket to the base assembly using four 5/16” x 1” hex bolts, 5/16” lockwashers and 5/16” hex nuts. See figure 3. 8. Attach the tool bracket to the base assembly using four 5/16” x 1” hex bolts, 5/16” lockwashers and 5/16” hex nuts. See figure 3. 6. Assemble a shoulder bolt and a 1/2” jam nut to each adapter bracket. See figure 2. ATTACHING BASE TO TRACTOR FAST ATTACH TRACTORS 9. Hook the base assembly under the shoulder bolts on the sides the tractor frame using the front notches in the base assembly. Align the hole in the bottom of the base assembly with the hole in the tractor drawbar. Insert the 5/8” x 1-3/4” hex bolt and secure it with the 5/8” hex nut. See figure 4. FIGURE 4 BOLTS FROM TRACTOR FRAME L.H. ADAPTER BRACKET R.H. ADAPTER BRACKET SHOULDER BOLT 1/2" JAM NUT 1/2" JAM NUT SHOULDER BOLT 5/16" x 1" HEX BOLT 5/16" HEX NUT 5/16" LOCK WASHER DRAWBAR BRACKET TOOL BRACKET BASE ASSEMBLY 5/8" HEX NUT 5/8" x 1-3/4" HEX BOLT SHOULDER BOLT STANDARD FRAME TRACTORS 10. Hook the base assembly under the shoulder bolts in the adapter brackets using the second notch in the base assembly. Align the hole in the bottom of the base assembly with the hole in the tractor drawbar. Insert the 5/8” x 1-3/4” hex bolt and secure it with the 5/8” hex nut. See figure 5. FIGURE 5 5/8" HEX NUT 5/8" x 1-3/4" HEX BOLT SHOULDER BOLT ASSEMBLING THE FRAME 11. Assemble the upright tubes to the base assembly using two 5/16-18 x 2" carriage bolts (from outside) and two 5/16" flat washers and plastic knobs (from inside). See figure 6. 5/16" x 2" CARRIAGE 1/4" x 1-1/2" SUPPORT ROD 1/4" HEX LOCK NUT HEX BOLT 1/4" x 1-1/2" HEX BOLT 1/4" HEX LOCK NUT FIGURE 7 15. Install a footrest clamp with preassembled bolt onto the front edge of each footrest, with the bolt underneath the footrest. See figure 8. 16. Raise the tractor's hood. Place the snow cab canopy onto the tubing frame, draping the front flap down in front of the tractor's dash panel. Lower the hood, trapping the front flap under the hood. Secure the sides of the canopy by fastening the elastic hooks to the bottom edge of the footrest and fender. Levers or handles on snowthrowers and snow blades should be located outside of the cab. See figure 8. BOLT 5/16" FLAT WASHER PLASTIC KNOB ...