inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. KEY PART NO. NO. DESCRIPTION REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1130SB-LSB (96193003800), PRODUCT NO. 961 93 00-38 2 2 1 3 4 5 6 7 8 9 10 11 12 13 14 13 14 12 11 10 9 8 7 6 5 4 3 1 2 2 23 17 20 19 16 18 24 22 23 21 22 17 18 15 16 20 19 21 01.15.001-A 1 532 40 51-61 COVER 2 532 18 44-71 SHOULDER SCRE

CHOKE ENGINE OIL GAS O LINE CONTROL FILL CAP / DIPSTICK FILLER CAP NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION. ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT. 12 FIG. 20 OPERATION TO START ENGINE Your snow thrower engine is equipped with both a 120 Volt A.C. electric starter and a recoil starter. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A.C. household current. • Be sure your house is a 120 Volt A.C. three-wire groun

21 22 REPAIR PARTS AUGER HOUSING / IMPELLER ASSEMBLY SNOW THROWER - MODEL NO. 1130SB-XLS (96193003000), PRODUCT NO. 961 93 00-30 KEY PART NO. NO. DESCRIPTION KEY PART 1 NO. NO. DESCRIPTION 2 01.07.016-A 1 532 42 17-26 AUGER ASSEMBLY 30 LH 2 532 42 17-27 AUGER ASSEMBLY 30 RH 1 2 3 (5x) 4 (5x) 01.07.023-B 1 532 42 17-13 AUGER HOUSING 2 532 40 76-45 SCRAPPER BAR 3 872 27 05-05 CARRIAGE BOLT 5/16.18 X .625 4 532 15 53-77 NUT 5/16.18 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4

(See “ENGINE” in the Maintenance section of this man ual). CYLINDER 1. Remove spark plug. 2. Pour one ounce (29 ml) of oil through spark plug hole into cylinder. 3. Pull recoil starter handle slowly a few times to dis trib ute oil. 4. Replace with new spark plug. OTHER • Remove safety ignition key; store it in a safe place. • Do not store gasoline from one season to another. • Replace your gasoline can if your can starts to rust. Rust and/or dirt in your gasoline will cause problems. • If possib

1130SB-LS (96193002900), PRODUCT NO. 961 93 00-29 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. KEY PART NO. NO. DESCRIPTION 1 2 3 4 6 6 7 8 7 8 8 9 9 5 5 10 10 01.08.011-A 1 532 42 17-08 PLOW HANDLE LH 2 532 42 17-09 PLOW HANDLE RH 3 532 19 69-44 PANEL BRACKET LH 4 532 19 69-43 PANEL BRACKET RH 5 532 41 45-1

6. Install left wheel (if removed for draining oil). Be sure to install klik pin into proper hole in wheel axle (See “TO REMOVE WHEELS” in the Service and Adjustments section of this manual). 7. Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine. 8. Refill engine with oil through oil dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man u al. 9. Use gauge on oil fill cap/dipstick for checking level. Be s

NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION 1 4 4 5 5 2 3 8 6 7 01.10.010-A 1 532 42 13-51 CONSOLE PANEL GRAY 2 532 42 14-48 HEADLIGHT BEZEL GRAY 3 532 17 86-66 HALOGEN HEADLIGHT 4 532 18 44-71 SHOULDER SCREW 10.24 X .625 5 532 17 52-62 SCREW 10.24 X 1.25 6 532 41 77-60 GRIP SWITCH 7 532 40 56-99 WIRE HARNESS 8 532 40 16-20 BULB REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. 1330SB-XLSB (96193004100), PRODUCT NO. 961 93 00-41 3 4 6 2 1 4 3 7 7 5 6 2 8 9 01.03.003-A KEY PART NO. NO. DESCRIPTION 1 5

ENGINE 1. Move throttle control to “STOP” position. 2. Remove (do not turn) safety ignition key to prevent unauthorized use. NOTE: Never use choke to stop engine. TO USE FUEL SHUT-OFF VALVE (See Fig. 11) The fuel shut-off valve is located beneath the fuel tank on the engine. Always op er ate the snow thrower with the fuel shut-off valve in the OPEN position. OPEN OFF Fig. 11 TO USE THROTTLE CONTROL (See Fig. 12) The throttle control is located on the engine. Always op er ate the snow thrower wit

• Throw snow downwind whenever possible. • Ad just the skid plates to proper height for current snow con di tions. See “TO ADJUST SKID PLATES” in this section of this manual. • For extremely heavy snow, re duce the width of snow removal by over lap ping previous path and moving slowly. • Keep engine clean and clear of snow during use. This will help air flow and extend engine life. • After snow-throwing is completed, allow engine to run for a few minutes to melt snow and ice off the engine. • Cl

• Make sure the discharge chute is pointed in a safe direction (no vehicles, buildings, people, or other objects are in the direction of discharge) before restarting engine. • Restart the engine, then squeeze the auger control lever to the handle to clear snow from the auger housing and the discharge chute. • Slower speeds are for heavier snow and faster speeds are for light snow and transporting the snow thrower. It is recommended that you use a slower speed until you are familiar with the oper