430355 10.19.09 SR Printed in the U.S.A. 20 NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. REPAIR PARTS SNOW THROWER - - MODEL NO. XT824ES (96192003302) AUGER HOUSING / IMPELLER ASSEMBLY 11 10 11 11 11 1 2 3 4 5 6 7 9 9 9 8 12 12 13 14 15 16 17 18 19 20 21 21 22 22 23 23 24 25 26 27 28 29 30 31 31 32 33 34 35

With chute rotator head and chute bracket aligned, spring. po si tion chute rotator head on pin and threaded stud of mounting bracket. 4. Install 3/8 washer and locknut on threaded stud and tighten securely. AUGER CONTROL ROD CONTROL ARM VINYL SLEEVE LOOP OPENING UP CHUTE ROTATOR HEAD 3/8 WASHER 3/8 LOCKNUT THREADED STUD PIN ROTATOR HEAD MOUNT ING BRACKET CHUTE BRACKET FIG. 7 ALIGN BEFORE TIGHTENING LOCKNUT FIG. 5 CHECK TIRE PRESSURE The tires on your snow thrower were overinflated at the factor

Snowthrower TRACTOR ASSEMBLY S/N 420280100101- 420280199999 85 0 J41 40 . . Ve TOUCH-UP PAINT SERVICE PARTS 200 Black Spray Paint 202 Loctite 242 201 Green Spray Paint 203 Tire Chains 7Г* Щ. 32 35 «к 29 Ч1 2 Model 42028 Ref.# Part# Description Qty. Ref.# Part# Description Qty. 1 1703539 Handle Grip............................................ 2 51 1756065021 Frame.................................................. . 1 2 1750796 Bumper..........................................

Do not use to start a warm en gine. • To engage choke, turn knob counterclockwise. Slowly turn knob clockwise to disengage. TO CONTROL SNOW DISCHARGE (See Fig. 12) WARNING: Snow throwers have ex- posed rotating parts, which can cause severe injury from contact, or from ma- terial thrown from the discharge chute. Keep the area of operation clear of all persons, small children and pets at all times including startup. WARNING: If the discharge chute or au ger become clogged, shut-off en gine and wa

If you think the engine-governed high speed needs adjusting, contact a service center/department, which has the proper equipment and experience to make any necessary ad just ments. TO ADJUST CABLE TENSION (See Fig. 25) Adjust cable tension by turning the adjuster turn buckle, located on the right hand cable. Grasp the long section tightly and turn the short section to lengthen the adjuster. Adjust until cable is snug. ADJUSTER TURN BUCKLE FIG. 25 TO REMOVE WHEELS (See Fig. 24) • Remove the klik

440575 11.09.10 TH Printed in U.S.A. IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. Look for this symbol to point out impor tant safety precautions. It means CAUTION!!! BE COME ALERT!!! YOUR SAFE TY IS IN VOLVED. WARNING: Always disconnect spark plug wire and place it where it can not con tact plug in order to pre v

3. Always refer to operator’s manual for important details if the snow thrower is to be stored for an extended period. 4. Maintain or replace safety and instruction labels, as necessary. 5. Run the machine a few minutes after throwing snow to prevent freeze-up of the collector/impeller. CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac tured to give best possible dependability and per for mance. Should you experience any problem you cannot eas

23 24 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802) HANDLES 34 37 42 10 15 23 22 27 27 22 15 32 31 32 30 31 38 39 7 6 36 2 5 5 5 1 8 28 28 9 18 19 26 24 24 25 5 5 29 40 12 11 15 11 11 15 16 17 16 17 14 13 REPAIR PARTS SNOW THROWER - MODEL PP10530ES (96192001802) HANDLES KEY PART NO. NO. DESCRIPTION 1 402682x479 Lever, Auger Control, RH 2 412681x479 Lever, Traction Drive Control LH 5 169675 Retainer, Hairpin 6 17060408 Screw, Hex Head 1/4-20 x 3/4 7 412677 Bail Control, Interlock 8 19

Use the clean-out tool to dislodge this blockage. When cleaning, repairing, or inspecting, make certain all controls are disengaged and the auger/ impellerandallmoving partshavestopped. Disconnect the spark plug wire and keep the wire away from the spark plug to prevent accidental starting. Releasethe auger control lever and shut offthe engine. -Removethe clean-outtool from it's mounting clip. Grasp the tool firmly by the handle and push and twist the tool into the discharge chute to dislodge th

Stop machine if anyone enters the area. 7. Exercise caution to avoid slipping or falling, especially when operating in reverse. Preparation 1. Thoroughly inspect the area where the equipment is to be used. Remove all doormats, newspapers, sleds, boards, wires and other foreign objects, which could be tripped over or thrown by the auger/impeller. 2. Always wear safety glasses or eye shields during operation and while performing an adjustment or repair to protect your eyes. Thrown objects which ri