Operator’s Manual 28” SNOW THROWER Model No. 247.887900 • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST • ESPANOL ® 7/6/2007 FORM NO. 769-02587A TABLE OF CONTENTS Warranty.Statement...................................Page.2 Repair.Protection.Agreement....................Page.3 Safe.Operation.Practices..........................Pages.4-5 Safety.Labels.............................................Page.7. Assembly...................................................Pages.8-11 Operation.......

• Stop engine and wait several minutes before checking oil level. Remove oil fill cap and dipstick. • Wipe dipstick clean, insert it into oil fill hole and tighten securely. • Remove dipstick and check. If oil is not up to the FULL mark on dipstick, add oil. Changing Oil Change engine oil after first two hours of operation and every 25 hours thereafter. In order to change the oil, you will have to first drain the spent engine oil from the engine and then refill with fresh oil. • Drain oil while

Use SAE 5W30 engine oil only. FILL OIL This snow thrower was shipped with a container of 5W30 oil. This oil must be added to the engine before starting. For extreme cold operating conditions of 0° F or below, use a partial synthetic 0W30 motor oil for easier starting. NOTE: In areas where temperature is consistently at 2CP F or lower, you may use 0W30 motor oil for easier starting. • Remove the oil fill cap/dipstick. • Pour the oil and fill the crankcase to line (Full) on dipstick (19 ounce

756-0625 Roller, Cable 31. 790-00096 Front Guide Bracket, Auger Cable 32. 790-00180A Frame 33. 790-00206A Guide Bracket, Auger Cable Ref. No. 34. Part No. 790-00207A Description Guide Bracket, Drive Cable 35. 790-00316 Cover, Frame 36. 634-04167A LH Wheel Assembly, 13 x 4 x 6 634-04168A RH Wheel Assembly, 13 x 4 x 6 37. 731-04873 Spacer, 1.25 x .75 x 3.0 38. 738-04168 Axle, .75 x 22” 39. 741-0919 Ball Bearing 40. 710-0809 Hex Screw, 1/4-20, 1.25, Gr5 41. 710-0191 Hex Screw, 3/8-24, 1.25, Gr8 42.

247.888520 CAUTION: Before using this product, read this manual and follow all Safety Rules and Operating Instructions. Sears, Roebuck And Co., Hoffman Estates, IL 60179, U.S.A. 770-10057B Printed in U.S.A. (10/98) TABLE OF CONTENTS TABLE OF CONTENTS Content Page Warranty Information .........................................2 Safe Operation Practices ...................................3 Assembly ...........................................................6 Operation ..............................

inches. 1 inch = 25.4 mm IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts. Failure to do so could be hazardous, damage your snow thrower and void your warranty. 45 BRIGGS & STRATTON 4-CYCLE ENGINE MODEL NUMBER 20M314-1370=E2 KEY PART KEY PART NO. NO. DESCRIPTION NO. NO. DESCRIPTION 528 793006 Hose-Primer 957 795027 Cap-Fuel 529 791822 Grommet 972 694260 Tank-Fuel 552 694674 Bushing-Governor Crank 975 698783 Bowl-Float 562 793216 Bolt (Governor Control Lever) 976 793

• Safety • Assembly • Operation • Maintenance • Parts PRINTED IN U.S.A. FORM NO. 49788 (REV. 7/05) Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. IMPORTANT - READ THIS FIRST!!! For Missing Parts or Assembly Questions Please Call 866-576-8388 Mon.-Fri. 7 am - 5 pm CST. FAX 217-728-2032 or e-mail info@agri-fab.com Missing parts will be sent UPS in 24 hours di rect ly to your home. ® TABLE OF CONTENTS ACCESSORIES...........................................................2 SAFETY RULES....

Failure to observe the following safety instructions could result in serious injury. & & Look for this symbol to point out ira= portant safety precautions. It means CAUTION!!! BECOMEALERT!!! YOUR SAFETY IS INVOLVED. & & WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent acci= dental starting when setting up, trans porting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surface

60684 U.SoA. SAFETY RULES CAUTION: ALWAYS DISCONNECT SPARK PLUG WIRE AND A PLACE WIRE WHERE IT CANNOT CONTACT SPARK PLUG TO & PREVENT ACCIDENTAL STARTING WHEN SETTING-UP, TRANSPORTING, ADJUSTING OR MAKING REPAIRS. IMPORTANT SAFETY STANDARDS REQUIRE OPERATOR PRESENCE CONTROLS TO MINIMIZE THE RISK OF INJURY. YOUR SNOW THROWER IS EQUIPPED WITH SUCH CONTROLS. DO NOT ATTEMPT TO DEFEAT THE FUNCTION OF THE OPERATOR PRESENCE CONTROL UNDER ANY CIRCUMSTANCES, FUEL .SAFETY BEFORE USE ® Read the owner's man

e Position the snow thrower so the oil drain plug isthe lowest point on the engine_ Remove the oil drain plug and oil fill cap/dipstick, Drain the oil into a suitable container. The oil will drain more freely when warm. Replace the oit drain plug and tighten securely_ Refill the crankcase with SA.E_ 10W-30 motor oi! (or equivalent)., S,A.E. 5W-30 motor oil may be used to make starting easier in areas where the temperature is consistently 20° F. or lower, SPARK PLUG o Make su re the spark plug is