Fold fastener back and under the side chain as pictured below. You will probably need pliers to do it. Once both fasteners are connected, chain assembly must be snug on tire. Advance fasteners on each side chain the same number of links until chain is sufficiently and evenly tight on tire. See front cover picture for proper chain fit. Remove or tie down all unused links once chain is satisfactorily tight. 5 Repeat previous steps for other tire. To get maximum wear and years of use from your

Please add the applicable color code, wherever needed, to the part number to order a replacement part. For instance, if a part, numbered 700-xxxx, is painted Cub Yellow, the part number to order would be 700-xxxx-0498. Cub Yellow: 0498 Cub Beige: 0499 Powder Black: 0637 17 Model 1333SWE 8 18 Model 1333SWE Ref. No. Part No. Description Qty. Ref. No. Part No. Description Qty. 1 736-0159 Flat Washer .344 ID x .875 OD 7 72 741-0184 Thrust Bearing .88 ID x 1.44 OD x 1 2 710-3015 Truss. Hd. Mach. Scr.

Press auger control handle to engage auger Turn handle to change discharge direction Figure 11 Stopping Engine • Run the engine for a few minutes before stopping to help dry any moisture on the engine. • To stop engine: Turn ignition key to OFF position and remove it from the snow thrower. IMPORTANT: Keep the ignition key in a safe place. Engine will not start without it. • Wipe all snow and moisture from the unit. Move the choke lever back and forth several times and leave it in the ON position

Replacing Belt • Remove the belt cover by removing five hex screws. See Figure 16. Hex Belt Cover Screws Figure 16 • Pull up on the idler pulley and slip the belt off the engine pulley. • Push down on the idler pulley and slip the belt off the auger pulley. • Reassemble new belt. See Figure 17. • Reinstall the belt cover. Figure 17 Auger Pulley Idler Pulley Engine Pulley Belt Engine • Refer to the separate engine operator’s manual packed with your snow thrower for all engine maintenance procedur

See Fig. 6-6. Off-Season Storage If the snow thrower will not be used for 30 days or longer, follow the storage instructions below. Lubricate the machine as instructed earlier in this section. Store in a clean, dry area. If storing the snow thrower in an unventilated area, rustproof the machine using a light oil or silicone to coat the snow thrower. Clean the exterior of the engine and the snow thrower. NOTE: Refer to the Tecumseh Engine manual packed with your machine for information on storing

NOTE: DO NOT use primer to restart a warm engine after a short shutdown. NOTE: Additional priming may be necessary if the temperature is below 15° Fahrenheit. 3. Grasp the recoil starter handle and slowly pull the rope out. At the point where it becomes slightly harder to pull the rope, slowly allow the rope to recoil. 4. Pull the starter handle with a firm, rapid stroke. Do not release the handle and allow it to snap back. Keep a firm hold on the starter handle and allow it to slowly recoil. 5.

If the engine falters, quickly rotate the choke control back toward FULL choke, and then slowly into the OFF position again. 6. When disconnecting the extension cord, always unplug the end at the three-prong wall outlet before unplugging the opposite end from the snow thrower. Recoil Starter 1. Rotate choke control to FULL choke position (cold engine start). NOTE: If the engine is already warm, place choke control in the OFF position instead of FULL. 2. Push the primer two or three times for col

Ignition Key The ignition key is a safety devise. It must be fully inserted in order for the engine to start. Remove the ignition key when the snow thrower is not in use. Important: Do not turn the ignition key in an attempt to start the engine. Doing so may cause it to break. Figure 4-1 Drive Control Headlight Oil Fill Fuel Cap Primer Choke Ignition Key Oil Drain Starter Button Electric Starter Outlet Recoil Starter Handle Chute Assembly Clean-Out Tool Auger Control Shift Lever Two-Way Chute Co

714-0143 Clik Pin 3. 784-5687A Auger Clutch Cable Bracket 27. 684-0042C Friction Wheel Assembly 4. 756-0625 Cable Roller 28. 656-0012A Friction Wheel Disc 5. 738-0924 Shoulder Screw 1/4-28 x .375 29. 684-0013B Wheel Shift Rod Assembly 6. 784-5630A Frame Assembly 30. 746-0897 Drive Cable 7. 741-0563 Ball Bearing 31. 748-0190 Spacer 8. 736-0105 Bell Washer 32. 684-0021 Friction Wheel Bracket Ass’y 9. 712-0116 Lock Jam Nut, 3/8-24 33. 732-0264 Extension Spring 10. 741-0598 Hex Flange Bearing 34. 71