Remove the key. To prevent accidental starting, disconnect the spark plug wire and fasten away from the plug. Problem Possible Cause Remedy Engine fails to start. Key is OFF. Push key in to the ON position. Failure to prime cold engine Press primer button twice and restart. Fuel valve is in CLOSED position. Turn valve to OPEN position. Out of fuel. Fill fuel tank. Choke OFF - cold engine. Turn choke to ON, set throttle to FAST. Engine flooded. Turn choke to OFF; try starting. No spark. Check gap

Pin B. Rear Hole of Lift Bar (Snowthrower Applications) C. Spacer D. Hair Pin Clip E. Upper Hole (Snowthrower Applications) F. Slot of Lift Link (Mower Applications) G. Lower Hole (Mower Applications) A B C D F E Figure 7. Install Lock Plate - Hydraulic Lift Models A. Lift Cylinder D. Lock Plate B. Flat Head Pin (Original) E. Hair Pin Clips C. Flat Head Pin (New) F. Lift Shaft Assy. 5 6 Installation Instructions Sub-Frame Hitch A C D E B Figure 8. Install Hitch A. J-Hooks D. Hook B. Hitch Rod E.

1695196 For Prestige / 1800 / 2800, Conquest / 1700 / 2700, & Broadmoor / 1600 / 2600 Series Tractors This kit is required when installing front mounted snowthrowers. 2 Installation Instructions Sub-Frame Hitch Early Manual Lift Only (See Instructions) Hydraulic Lift 47 16 28 27 25 33 40 41 39 38 37 36 43 51 42 33 25 29 29 29 28 28 27 50 17 13 11 14 9 12 13 11 19 18 21 20 10 24 23 7 8 9 9 22 15 9 25 49 22 31 30 30 25 27 28 27 33 25 34 32 3 2 1 4 5 6 33 25 28 25 27 26 27 28 35 Front Hole for Doze

No. Description 1695303 P1524E, Snowthrower 1695304 P1524EX, Snowthrower (CE) 1628 Models Mfg. No. Description 1695305 P1628E, Snowthrower 1695306 P1628EX, Snowthrower (CE) 1732 Models Mfg. No. Description 1695307 P1732E, Snowthrower 1695308 P1732EX, Snowthrower (CE) 1738 Models Mfg. No. Description 1695309 P1738E, Snowthrower 1695310 P1738EX, Snowthrower (CE) 1695358 P1738E, Snowthrower 1695359 P1738EX, Snowthrower (CE) 1734900 Revision 01 Rev. Date 8/2007 TP 100-4585-01-LW-SN Table of Contents

WARNING Gasoline and its vapors are extremely flammable and explosive. Fire or explosion can cause severe burns or death. When starting the engine, ensure that spark plug, muffler, fuel cap and air cleaner are in place and secured. Do not crank engine with spark plug removed. If engine floods, set choke (if equipped) to open/run position. WARNING Engines give off carbon monoxide, an odorless, colorless, poison gas. Breathing carbon monoxide can cause nausea, fainting or death. When starting the

B) EN ® Loosen upper fasteners. ® Remove lower fasteners. ® Carefully lift handle to the operating position while guiding the speed control rod over the tire. ® Make sure Z-fittings are secured in holes of control levers. © Make sure cables are not caught between the upper and lower handle. © Reinstall lower fasteners. Tighten upper and lower fasteners securely. ® Use the supplied ties to secure the EZ Turn cable (if equipped) to the left handle. FR ® Desserrez les fixations supérieure

. Fill tank to approximately 3.8 cm (1-1/2 in.) O below top of neck to allow for fuel expansion. If fuel spills, wait until it evaporates before starting engine. Keep fuel away from sparks, open flames, pilot lights, heat, and other ignition sources. Check fuel lines, tank, cap, and fittings frequently for cracks or leaks. Replace if necessary. STARTING ENGINE Fig. 4 CAUTION: The manufacturer of the equipment on which this engine is installed specifies top speed at which the engine will

Torque the three set screws (B, D) to 9-11 ft. lbs. 2 Gear Case Kit Installation Instructions Assemble Housing 1. Install the side covers (A, Figure 4) and secure with the original hardware. 2. Reinstall the bearings (C), washers, and retaining rings (D) in both side covers. Figure 4. Assemble Housing A. Side Cover B. Housing C. Bearing D. Washers & Retaining Ring Fill Auger Gear Case Oil 1. Remove the fill plug (Figure 5). Fill the gear box with The Dealer Line Winter Weight Worm G

14 727291 SCREW, 5/16-18 x .63 15 727940 SCREW, 1/4-20 x 2.00 16 727517 PLATE, Mounting Support 17 722305 SUPPORT, Frame 18 722320 FRAME, R.H. 19 722633 SCREW, 5/16-18 x 3/4 20 1740032 RING, Foam 21 724068 CLAMP, Fuel Line, Screw Type 22 723210 SCREW, 1/4-20 x 5/8 Footnotes: 522 SINGLE STAGE SNOW THROWER Manual No. 7006053 SERIES 0 TP 400-5245-IR-SX-N 13 Engine Drive System Group Manual No. 7006053 522 SINGLE STAGE SNOW THROWER TP 400-5245-IR-SX-N SERIES 0 14 Engine Drive System Group Item Part