valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
PATENTS 5,532,710 and 5,554,998 Made in U.S.A. IMPORTANT: INSTALL POINT OF BASE TOWARD FRONT OF VEHICLE! Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 319/754-0600 • FAX 319/754-0787 Printed in U.S.A. ©Winegard Company 2001 2451142 Rev. 6/05/01 INSTALLATION & ASSEMBLY STEP 1. Choose a location for antenna that will allow it to rest in travel position with antenna pointing toward rear of vehicle and raise and rotate without interfering with other roof-mounted equipment. Make sure inside ceiling area is clear where ceiling plate will mount. NOTE: Figure 1 shows minimum distance (10") antenna should be located from edge of vehicle roof. We recommend you check with your dealer or the manufacturer to see what provisions have been made in the roof for antenna mounting. A reinforced area of roof as well as pre-wire downlead may be available. NOTE: The system must be level for proper operation. If you have a curved roof you should use a Winegard Model RW-1000 wedge kit to level the system. STEP 2. Position template on roof (last page of manual) and drill a 1-1/2" hole through roof and ceiling of vehicle. Take care to avoid damage to wiring which may run between roof and ceiling. 2 It is highly recomended that the antenna be mounted on roof center line. Do not mount antenna closer than 10" from edge of roof. RW-1000 Roof Wedge Vehicle Roof Interior Roof Antenna Controls Wedge, Optional NOT TO SCALE Rev. 2/2001 FIGURE 1 STEP 3. Attach reflector to backup assembly as shown in Figure 2. STEP 3. Attach reflector to backup assembly as shown in Figure 2. boot collar. (4) 5/16-18 x 5/8" Flat Head Bolt RS-1000 Antenna Reflector Attach coax cable to F-jack on antenna, slide weather boot over boot collar. Attach RS-1000 to elevating tubes using E-clips and pins supplied. (4) 5/16-18 Hex Nut Backup Assembly (4) 5/16" Flat Washer NOTE: Make sure that coax cables fits between the reflector and the fixed feed arm. ANTENNA SHOWN PARTIALLY RAISED FOR EASE OF ILLUSTRATION ONLY FIGURE 2 Rev. 2/98 STEP 5. The mount is designed to fit roofs 1" to 4 3/4" thick. If roof is less than 4 3/4" thick, cut elevating shft and directional handle to size. (See table below.) If roof is more than 4 3/4" thick, the RP-2000 Thick Roof Kit is required. See page 15, A for chart. STEP 5. The mount is designed to fit roofs 1" to 4 3/4" thick. If roof is less than 4 3/4" thick, cut elevating shft and directional handle to size. (See table below.) If roof is more than 4 3/4" thick, the RP-2000 Thick Roof Kit is required. See page 15, A for chart. , ADD 1/2" TO ELEVATING SHAFT LENGTH GIVEN BELOW, BUT NOT TO THE DIRECTIONAL HANDLE. ROOF ELEVATING SHAFT W/RW-1000 DIRECTIONAL THICKNESS LENGTH HANDLE LENGTH 4 3/4" 6 1/4" RP-4200 req. 5 3/8" 4 1/2" 6" RP-4200 req. 5" 4 1/4" 5 3/4" 6 1/4" 4 3/4" 4" 5 1/2" 6" 4 1/2" 3 3/4" 5 1/4" 5 3/4" 4 1/4" 3 1/2" 5" 5 1/2" 4" 3 1/4" 4 3/4" 5 1/4" 3 9/16" 3" 4 1/2" 5" 3 3/8" 2 3/4" 4 1/4" 4 3/4" 3 1/16" 2 1/2" 4" 4 1/2" 2 3/4" 2 1/4" 3 3/4" 4 1/4" 2 3/8" 2" 3 1/2" 4" 2 1/16" 1 3/4" 3 1/4" 3 3/4" 1 3/4" 1 1/2" 3" 3 1/2" 1 3/8" 1 1/4" 2 3/4" 3" 1" Direc- tional Handle STEP 6. Mount antenna and lift on roof in travel position. Apply approved sealing compound suitable for your vehicle roof on bottom of base plate and roof area around hole. See Figure 3. Secure base plate with screws provided, except for screw indicated in Figure 3*. STEP 7. Attach cable clamp to the coax cables 16" from the cable clamp on the gear housing. STEP 8. Attach cable clamp to roof of RV as shown in Figure 3, use 7/16" flat washer between screw and cable clamp, apply sealing compound over mounting screw heads. STEP 9. Attach satellite antenna coax cable (has "RG-6" printed on it) to the coax cable going to the satellite receiver. STEP 10. Attach RS-1000 coax downlead (has "RG-59" printed on it) to coax downlead going to RV-0541 power supply. Refer to power supply instruction sheet. You can connect the antenna output from the power supply directly to the satellite receiver (refer to receiver manual). This Rev 1/2001 allows you to watch local channels when you turn the receiver off. CAUTION: DO NOT GET SEALING COMPOUND ON BEARING SURFACE BETWEEN BASE PLATE AND ROTATING GEAR HOUSING. DO NOT PAINT TOP OF BASE PLATE OR AROUND ROTATING GEAR HOUSING. NOTE: Apply sealant approved for your vehicle roof between Base Plate and roof of vehicle. 3" min. Cable clamp on gear housing. FIGURE 3 Cable TiesMake sure cable entry is sealed CAUTION: DO NOT GET SEALING COMPOUND ON BEARING SURFACE BETWEEN BASE PLATE AND ROTATING GEAR HOUSING. DO NOT PAINT TOP OF BASE PLATE OR AROUND ROTATING GEAR HOUSING. NOTE: Apply sealant approved for your vehicle roof between Base Plate and roof of vehicle. 3" min. Cable clamp on gear housing. FIGURE 3 Cable TiesMake sure cable entry is sealed Apply approved sealant under lip and cable roof hole #10 x 1" Screws STEP 11. Feed downleads through roof using Winegard Model CE-2000 cover plate (included with hardware). Weatherpro...