valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
Select the transponder that gives you a signal strength of 85%. . Press . two times to return to SETUP menu. 39 qSat Setup Sat Ports Dish Pos Sig Meter Zip code for position 92154 Elevation Azimuth Tilt Press uto change the zip code. Enter zip code, press ACTION ROLLERGUIDEMENUOPERATIONS Setup : Monitor The monitor menu allows you to match your monitor/receiver type. You can choose between two monitor types: 16:9 or 4:3 aspect ratio. Monitor System Test Access Card TV Output uSat Setup Press u to set monitor aspect ratio. u 4:3 Aspect Panasonic Standard TV Setup : Monitor Screen The following table shows the icon and messages displayed for each of the monitor types. Type Picture Icon Message 4:3 Panasonic “Standard TV” 16:9 Panasonic “DTV Wide Screen” Procedure • In SETUP menu, press q button to select Monitor. • Press u button to highlight Monitor. • Press • button to change monitor aspect ratio. • Press pq buttons to select 4:3 or 16:9. • Press ACTION button to save the selection. 40 ROLLERGUIDEMENUOPERATIONS Setup : System Test The System Test menu allows you to invoke a system test which perform a check of the following subsystems. Component Requirement Display Information Tuning Test This attempts to tune to an known frequency. Status: PASSED or FAILED Signal Test This tests the signal strength. Status: PASSED or FAILED Phone Test This checks the modem operational status. Status: PASSED or FAILED Access Test This checks the Access Card function. Status: PASSED or FAILED Card ID Card is installed in TZ-DBS01 Serial # xxxx-xxxx-xxxx Note: System test is only available for Satellite input. The following screens show the system test screen and the system test in progress. Monitor System Test uSat Setup Press u to start system test. Card ID Access Phone Signal Tuning Start Status: Status: Status: Status: Monitor System Test uSat Setup Press ACTION to start the system test. Card ID Access Phone Signal Tuning Start Status: Status: Status: Status: PASSED PASSED PASSED CHECKING 322452186 Access Card TV Output Access Card TV Output System Test Screen System Test Screen (System Test in progress) Procedure • In SETUP menu, press p or q button to highlight System Test. • Press • button to highlight Start. • Press ACTION button to start the System Test. • Press t button to return to Setup Menu. 41 ROLLERGUIDEMENUOPERATIONS Setup : Access Card The Setup screen allows you to setup a new access card. You can transfer existing access card information to the new access card. This procedure is called “chaining”. When you press the ACTION button while the Access Card is highlighted, a series of Conditional Access driven menus will be displayed. This will direct you on what procedures to perform. Monitor System Test Access Card uSat Setup TV Output Press ACTION to set up a new access card. New Card Configuration: Please insert the old Card and press the ACTION key. This will start the Card duplication procedure. Access Screen (Entry Point) Procedure • In SETUP menu, press p or q buttons to highlight Access Card. Follow the directions displayed on-screen. • Press ACTION button to setup a new access card. • Press • button to return to Rollerguide menu. Note: This procedure can only be used in the case where a new card is provided by DIRECTV and is different from the card that comes with the unit. 42 ROLLERGUIDEMENUOPERATIONS TV Output This menu lets you set the RF output of the Digital Satellite Receiver to either CH 3 or CH 4. You can connect the Digital Satellite Receiver to your television, even if your TV does not have video inputs. Monitor System Test Access Card uSat Setup TV Output Press u to change TV output settings. Channel u 4 Warning: Television must be set to the selected channel! TV Output Screen Procedure • In SETUP menu, press • or • buttons to highlight TV Output. • Press • to change the TV output settings. • Press p or q to select CH 3 or 4. • Press ACTION button to save the selection. Note: Prior to adjustingthisfeature, makesurethat your TVis set either CH 3 or 4. TV output channel that you selectin the SETUP menu should be the same as the television. 43 ROLLERGUIDEMENUOPERATIONS Guide The Advanced Program Guide™ (APG) is a key feature of the Digital Satellite Receiver. The Guide enables you to browse through a large number of programs and provides useful information upon user request, as shown below. Guide: Full Screen If the user tries to access the Guide while it is acquiring data from the satellite signal, a message will be displayed showing the graphical countdown clock of when the Guide will be ready for display. Acquiring data... 6 80% Please Wait... 100% Guide : Acquisition Delay window100% Acquisition Window Tuning to a Program You can select a program by highlighting the program in the Guide and pressing ACTION button on the remote control or by directly entering the desired channel number using the remote control number keys and pressing the ACTION button. 44 ROLLERGUIDEMENUOPERATIONS Guide : Ch...