valutazioni - 2, GPA: 3 ( )

Produttore : Winegard File Size : 1.17 mb File Nome : Lingua di insegnamento:

Be sure the mount has not been damaged. 2. Check for caulking on elevating shaft. 3. Contact your dealer or Winegard Technical Services. LCD DISPLAY CODES HL................High Limit LL..................Low Limit Lo................Batter Low Er.........................Error --..................Initializing NOTE: Initialization may take up to 5 seconds. 3. 4. 5. 6. 7. 8. 9. 1 2 4 7/09/04 Assembly & Installation Things you need — Screwdrivers (Phillips and slot) 1-3/4” hole saw 7/16” wrench ABS glue Drill with 1/8” bit Tape measure Non-hardening sealant (Check manufacturer’s specifications for compatibility with your roof material.) FIGURE 3 Winegard’s Digital Elevation Sensor has been INSTALLED and CALIBRATED at the factory STEP 1. Choose a location on the roof for dish that will allow dish to raise and rotate without interfering with other roof-mounted equipment. Make sure inside ceiling plate is easily accessible, and with no obstructions that would interfere with operation. Figure 3 shows minimum distance (10”) antenna should be located from edge of vehicle roof. It is recommended that you check with your dealer or manufacturer for provisions that may have been made in the roof for antenna mounting; a reinforced roof area or pre-wire installation from the factory. note: The system must be level for proper operation! Winegard Model RW-5000 roof wedge with gasket is available. If inside roof wedge is needed, Winegard’s RW-2000 can be trimmed to fit ceiling plate. STEP 2. Position template on roof (see insert page of this manual). CAUTION: DO NOT drill through wiring. Carefully drill a 1-3/4” hole through roof and ceiling of vehicle. Inspect hole to make sure wiring is intact. (Roof template, see insert.) It is highly recommended the antenna be mounted on roof center line. Do not mount antenna closer than 10” from roof edge. NOT TO SCALE Rev/7/9/04 5 STEP 3. Attach dish to backup. Use bolts and nuts provided, Figure 4. STEP 4. Mount dish on roof in upright position. Rotate clockwise to stop, Figure 5. Dish will be toward back of vehicle when in stowed or travel position. The word FRONT is embossed on the base and should face the front of vehicle. Secure to roof using screws (provided). The travel bracket sjhould be mounted to roof 6-1/8” from base of dish, toward back of vehicle. See Figure 6. NOTE: Apply non-hardening sealing compound to screw heads, coax access hole and edge of gasket under mount base. Install the vent tube on the back of the mount base (the is the side opposite the word FRONT). The hole for the vent tube is shown in Figure 6A. CAUTION: DO NOT seal hole in vent tube. Put sealant around the outside of the vent tube, approximately 1/2” from end. Push vent tube into the hole. The sealant will seal the hole as you push in vent tube. Leave approximately 2 to 2-1/2” of the vent tube extending from the hole. Put a small amount of sealant on the roof under the vent tube end to hold in place. FIGURE 6A Vent tube Sealant CAUTION: DO NOT GET sealing compound between Base Plate and Rotating Gear Housing. DO NOT PAINT top of Base Plate or around Rotating Gear Housing. STEP 5. Facing the front of the dish, note the coax attached to the side of the feed arm. Meaure 24” coax from this point. DO NOT CUT. Put coax around mount base, Figure 5. STEP 6. Apply approved sealing compound over mounting screw heads. STEP 7. Feed coax through the roof using cover plate (included, w/hardware), Figure 7. Weatherproof cable entry by applying sealant under lip of cable entry plate and where cable enters roof. Attach plate to roof with screws provided. Apply sealant over screws and around edge of roof-thru plate, making sure cable entry is sealed. If downlead connection is made on top of roof, make sure to weatherproof connection! Rotate clockwise to stop. FIGURE 5 Measure 24” of coax at plastic fastener on left side of feed arm. (See Step 5.) No cable clamps on this part of cable. Install cable entry plate 3” minimum from mount base. ANOTHER METHOD OF IBSTALLING ROOF/CABLE ENTRY PLATE: Attach cable to roof using cable clamp. Use sealant to seal screw heads. #10 x 1” Screws FIGURE 7 CE-2000 Downlead connects to satellite receiver Downlead FS-8100 Male-to-male F-connector Rev. 6/06/03 6 DIGITAL ELEVATION SENSOR ROOF CONNECTIONS The illustrations below show the different methods of connecting wires at roof level; method will depend on model. Wire colors MUST MATCH, ie. red to red, green to green, black to black. INSIDE RV Supplied with DM-2000 only 3M UR TERMINAL DO NOT STRIP ^ wires, terminal is self-stripping. Slide wires all the way in. NOTE: This terminal is weatherproof and can be left outside on the roof IF SECURED PROPERLY to prevent wind whipping. Squeeze pliers until red plunger is flush with res of terminal. (Pliers not supplied.) Special instructions: For roof thickness greater than 6-1/2”. Parts Needed: (not included) RP-4400 14” worm ...

Scarica la tua

Per scaricare, digitare 2 cifre :