Er ist mit einem optischen Audio-Ausgang zum Anschluss an eine Dolby-Digital-Anlage ausgestattet, mit der Sie sich den KinoTon in Ihr Wohnzimmer holen können. Der Anschluss einer aktiven DVB-T-Antenne ist ohne zusätzliches Netzteil möglich. Der Receiver UFT 671si wird in der Gehäusefarbe Silber geliefert. Merkmale ■ Empfang von freien digitalen terrestrischen TV- und Radio-Programmen ■ Tuner mit Durchschleif-Ausgang ■ 1.000 Programm-Speicherplätze ■ Menügeführte Erst-Installation ■ Elekt

3 Front panel and infra red sensor............................................................................................................... 4 Rear panel connections............................................................................................................................ 4 Remote control operating buttons............................................................................................................. 4 Safety Information.........................................

Um die Einhaltung der EMV-Forderungen zu gewahrleisten, mussen nicht benutzte Anschlusse mit 75 . (z.B. EMK 03) abgeschlossen werden. DiSEqC™ ist ein eingetragenes Warenzeichen der European Telecommunications Satellite Organisation. The switching matrix meets the requirements set by the guidelines 73/23/EEC(low voltage guideline) and 89/336/EEG (EMC guideline) that were valid at the time of delivery. In order to ensure that the EMC requirements are observed, unused connections of 75 . (e.g. EMK

3 Front panel and infrared sensor................................................................................................................ 4 Rear panel connections............................................................................................................................ 4 Remote control handset keys ................................................................................................................... 4 Safety instructions......................................

We reserve the right to make changes to this manual without prior notice. This particularly applies to modifi cations required for technical improvement. We appreciate your recommendations and suggestions for improvement. Publications, copies and print-outs as well as electronic distribution of this manual in full or in part is only allowed with written authorisation from the Kathrein-Werke KG. All product names and trademarks used in this manual are the property of the relevant companies. VALID

4. When selecting the antenna site, you must consider the structural characteristics of the building. Installation on the edge of rooftops or buildings and on cylindrical structures could lead to increased wind loads and vibration stress according to DIN 1055, part 4, or DIN 4131. Non-observance of these instructions may cause exceeding of the load limit or the vibration resistance. 5. Do not install the antenna on buildings with easily in ammable materials as rooftop, such as straw, reed or sim

Select any programme on the TV set or the measurement device for the antenna alignment. After nishing the alignment, tighten the wing screws on the mast clamp. Indication of the reception of DVB-T signals Kathrein antennas are pre-assembled for the reception of horizontally polarised signals. However, DVB-T signals are also transmitted in vertical polarisation. For DVB-T reception, turn the antenna in its longitudinal alignment to the transmitter rotated 90° counterclockwise. Observe the directi

The wind load absorption of the tube has already been allowed for. The bold values apply for an ordinary wind load (q = 800 N/m2). In case of increased wind load (q = 1100 N/m2), the reduced values apply. According to EN 50083-1, the mast clamping length must be at least 1/6 of the mast length. 2) The technical data underlie the computation base according to DIN 4131. If the sum of the antenna wind load moments exceeds the values put in parentheses (. 1650 Nm am Einspannpunkt), a structural anal

Open the cable pull-secure clamp and the cable connection clamp. 4. Connect the cable and clamp in rmly. 5. Replace the cover and screw down rmly. 6. Install the cable so that it does not atter or is under any friction (e.g. with cable ties, isolating band or cable clamps). 7. To ensure that no water can ow into the mast or seep into walling lay the cable with a drip-bend ( g. 5). Antenna alignment Align the antenna for optimum reception by turning it. If necessary, use an antenna measurement de

No liability can be assumed for any mistakes that may still be contained in the manual or for any damage resulting from such mistakes. This manual may not be copied in full or in part nor reproduced nor distributed in any other form without written permission from Kathrein KG. We reserve the right to make alterations to this manual without prior notice. This applies in particular to alterations required for technical improvement. All product names and trademarks used in this manual are the prope