Er ist mit einem optischen Audio-Ausgang zum Anschluss an eine Dolby-Digital-Anlage ausgestattet, mit der Sie sich den KinoTon in Ihr Wohnzimmer holen können. Der Anschluss einer aktiven DVB-T-Antenne ist ohne zusätzliches Netzteil möglich. Der Receiver UFT 671si wird in der Gehäusefarbe Silber geliefert. Merkmale ■ Empfang von freien digitalen terrestrischen TV- und Radio-Programmen ■ Tuner mit Durchschleif-Ausgang ■ 1.000 Programm-Speicherplätze ■ Menügeführte Erst-Installation ■ Elekt

HOTBIRD). No signal! Signal 7. After this, the following insertion will appear partial picture appears above at right. and after another few seconds the desired TV programme is shown as full picture: 6. If the satellite signal is found, at first only a small Do not stop the search now, since the receiver undertakes a fine tuning in order to optimize signal reception! (This procedure may last up to two minutes depending on the reception situation) 936.2412/ZWT Note: The F-button of your remote co

All Rights Reserved Printed in the U.S.A. REVISION HISTORY ISSUE DATE REASON FOR CHANGE 1 07/2006 Original. 2 04/2007 Updated for new card configuration (Fiber Interface Controller replaces Synchronous Interface Card). Expanded to include NXD descriptions and settings. Updated for other general changes in format and content. TRADEMARK INFORMATION Digivance is a registered trademark of ADC Telecommunications, Inc. ADC is a trademark of ADC Telecommunications, Inc. DISCLAIMER OF LIABILITY Contents

The Kathrein-Werke KG has made every effort to ensure that the data and descriptions in this manual are accurate and complete. We reserve the right to make changes to this manual without prior notice. This particularly applies to modifications required for technical improvement. We appreciate your recommendations and improvement suggestions. Publications, copies and print-outs as well as electrical distribution of this manual in full or in part is only allowed with written authorisation from the

4. When selecting the antenna site, you must consider the structural characteristics of the building. Installation on the edge of rooftops or buildings and on cylindrical structures could lead to increased wind loads and vibration stress according to DIN 1055, part 4, or DIN 4131. Non-observance of these instructions may cause exceeding of the load limit or the vibration resistance. 5. Do not install the antenna on buildings with easily in ammable materials as rooftop, such as straw, reed or sim

Open the cable pull-secure clamp and the cable connection clamp. 4. Connect the cable and clamp in rmly. 5. Replace the cover and screw down rmly. 6. Install the cable so that it does not atter or is under any friction (e.g. with cable ties, isolating band or cable clamps). 7. To ensure that no water can ow into the mast or seep into walling lay the cable with a drip-bend ( g. 5). Antenna alignment Align the antenna for optimum reception by turning it. If necessary, use an antenna measurement de

Select any programme on the TV set or the measurement device for the antenna alignment. After nishing the alignment, tighten the wing screws on the mast clamp. Indication of the reception of DVB-T signals Kathrein antennas are pre-assembled for the reception of horizontally polarised signals. However, DVB-T signals are also transmitted in vertical polarisation. For DVB-T reception, turn the antenna in its longitudinal alignment to the transmitter rotated 90° counterclockwise. Observe the directi

The wind load absorption of the tube has already been allowed for. The bold values apply for an ordinary wind load (q = 800 N/m2). In case of increased wind load (q = 1100 N/m2), the reduced values apply. According to EN 50083-1, the mast clamping length must be at least 1/6 of the mast length. 2) The technical data underlie the computation base according to DIN 4131. If the sum of the antenna wind load moments exceeds the values put in parentheses (. 1650 Nm am Einspannpunkt), a structural anal

After having pressed the F-button, the present satellite position is approached; if there is no signal, the OSD for point 5 will appear. Then continue the procedure as mentioned under point 5. CAP 200 and 300/HDP 170 Short User Guide Possible fault messages and their causes 1. Initalisation OSD does not disappear (not even after 20 seconds) • Check the connection between receiver and control unit • Control in the main menu if the HDP mode (antenna positioning) on the receiver was switched off 2.

F Vous pouvez obtenir un manuel d‘installation en francais chez notre representant en votre pays (ou le telecharger de notre page d‘ouverture (Lei puo avvere la versione italiana delle istruzioni di montaggio dalla nostra rapresentanza (piu vicina della sua citta., oppure scaricarla dalla nostra hompage ES Para obtener la version espanola de nuestro manual de instalacion, contacte nuestros representantes en su pais (o bajela de nuestra pagina de Internet (Electronic equipment is not household wa