Figure 63. Thread dial gear engaged with leadscrew. Cap Screw Dial Gear -43 Figure 67 Model SB1001 8K™ Lathe OP E R A T ION For Machines Mfg. Since 8/11 When threading, we recommend using the slowest speed possible and avoiding deep cuts, so you can more easily disengage the half nut to prevent an apron crash! Thread Dial Chart Find the TPI (threads per inch) that you want to cut in the left column of the thread dial chart (see Figure 64), then reference the dial number to the right of it. The d

Repeat this process and move the carriage left/ right and the cross slide forward/backward to distribute oil along the way guides. Lubricate the guides once before and once after operating the lathe. If the lathe is in a moist or dirty environment, increase the lubrication interval and make sure to keep the oil level full. . Location of way pump, fill plug, and sight glass on the apron. Sight Glass Fill Plug Way Pump Unpainted & Machined Surfaces Besides the ways and leadscrew, all other unpaint

Follow federal, state, and fluid manufacturer requirements for proper disposal. Cutting Fluid System The cutting fluid system delivers cutting fluid through a positionable nozzle and is turned ON/ OFF by the control panel cutting fluid pump switch and the valve lever near the base of the nozzle hose (see Figure 100). Figure 100. Coolant system controls and components. Cutting Fluid Pump Switch Nozzle Valve Lever Running the pump without adequate fluid in the tank may permanently damage it. This

5. Cover and place the machine in a dry area that is out of direct sunlight and away from hazardous fumes, paint, solvents, or gas. Fumes and sunlight can bleach or discolor paint and make plastic guards cloudy. 6. Once or twice a month, depending on the ambient humidity levels in the storage environment, wipe down the machine as outlined in Step 3. 7. Every few months, start the machine and run all gear-driven components for a few minutes. This will keep the bearings, bushings, gears, and shaft

Except for the differences noted in this insert, all other content in the Model SB1014 Owner’s Manual applies to this machine. Before operating your new lathe, you MUST read and understand this insert, the entire Model SB1014 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of injury when using this machine. Keep this insert for later reference. If you have any further questions about this manual insert or the differences between the Model SB1014F and the Model SB1014, contact

-8 For Machines Mfg. Since 7/09 PREP A R A T I O N EVS Toolroom Lathes Inventory Main Inventory 1: (Figure 2) Qty A. Steady Rest Assembly ....................................1 B. 12" Faceplate w/D1-6 Camlock Stud Set ......1 C. 10" Four-Jaw Chuck w/Combo Jaws .............1 D. Four-Jaw Chuck Key .....................................1 E. Four-Jaw Chuck D1-6 Camlock Stud Set .....1 F. Follow Rest Assembly ....................................1 Tool Box Inventory: (Figure 3) Qty G. Tool Box ........

However, because of the many variables involved with shipping, we recommend that you at least verify the following adjustments to ensure the best possible results from your new machine. Step-by-step instructions for these adjustments can be found on the pages referenced below. Factory adjustments that should be verified: ... ..........................................Page 34). ... ................................................................... adjustment (Page 65). ... .......................

Box 2027, Bellingham, WA 98227 U.S.A. PHONE: (360) 734-1540 • © South Bend Lathe Co. Model SB1037F 16" x 40" Lathe 220V with DRO Product Dimensions Weight...........................................................................................................................................................3107 lbs. Width (side-to-side) x Depth (front-to-back) x Height..................................................................... 86 x 33 x 60 in. Footprint (Length x Width).........

Mounting Dead Center in Spindle 1. DISCONNECT LATHE FROM POWER! 2. Thoroughly clean and dry the tapered mating surfaces of the spindle bore, tapered sleeve, and the center, making sure that no lint or oil remains on the tapers. 3. Insert the center into the sleeve, then insert the sleeve into the spindle bore through the chuck or faceplate. Figure 66 shows an example of the dead center installed in the spindle, using a lathe dog and faceplate for turning between centers. Dead Center Figure 66. E

Before operating your new lathe, you MUST read and understand this insert, the entire Model SB1038 Owner’s Manual, and the Fagor DRO Owner’s Manual to reduce the risk of injury when using this machine. Keep this insert for later reference. If you have any further questions about this manual insert or the differences between the Model SB1038F and the Model SB1038, contact our Technical Support at (360) 734-1639 or email sales@southbendlathe.com. New & Changed Parts 2318 2407 2416 REF PART #