valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Do not program an H3 spin after this step. Da Drain to optional reuse tank A Db Drain to optional reuse tank B F Heat select temperature in ° Fahrenheit C Heat select temperature in ° Centigrade HF Hot flush HH Hot fill to high level HM Hot fill to medium level aL Fill from reuse tank A to low level SEt UP Perform model setup routine aM Fill from reuse tank A to medium level Display Interpretations aH Fill from reuse tank A to high level bL Fill from reuse tank B to low level bM Fill from reuse tank B to medium level bH Fill from reuse tank B to high level HL Hot fill to low level HO Hot fill to overflow HR Hot rinse H1 High speed #1 H2 High speed #2 H3 High speed #3 (default) H3 High speed #3 (maximum) HT Heat (steam or electric) --M Minutes (used when programming time) --S Seconds (used when programming time) MS Medium speed spin SK Soak S1 Supply #1 (Detergent) S2 Supply #2 (Bleach) S3 Supply #3 (Sour) S4 Supply #4 (Softener) S5 Supply #5 (Specialty) TH Controlled temperature fill to high level TM Controlled temperature fill to medium level TL Controlled temperature fill to low level TO Controlled temperature overflow W1 Wash 1 (normal reversing) W2 Wash 2 (gentle reversing) W3 Wash 3 (no agitation) W4 Wash 4 (medium reversing action) TEST?/ SPEED Test rotation sensor W5 Wash 5 (temp.-controlled cool-down) Table 1 Table 1 F232201 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation Display Interpretations W6 Wash 6 (extra low agitation) W7 Wash 7 (no agitation, drain 1 open, no refill) WD Wash drain step – shortest drain time. Use only if not followed by a spin step. Drain 1 open, no rotation. WF Warm flush WH Warm fill to high level WM Warm fill to medium level WL Warm fill to low level WO Warm fill to overflow level WR Warm rinse • Left dot–poor balance condition • Second dot from left–door lock switch • Third dot from left–Program Mode • Fourth dot from left–high level reached • Fifth dot from left–medium level reached • Right dot–low level reached EXISTS Cycle already in memory EDIT? Do you want to edit the cycle? TEMP Over-temperature-limit condition OVERHT Open or shorted temperature input circuit or temperature out of computer’s allowable limits WATER Water in washer-extractor at end of cycle °FAR Temperature in degrees Fahrenheit °CEN Temperature in degrees Centigrade MANUAL Manual Mode enabled NO MAN Manual Mode disabled 1DRAIN One drain capability selected 2DRAIN Second independent drain enabled (via Auxiliary 2 output–precludes control of recirculation pump via Auxiliary 2, if selected). This should not be confused with the “dual drain” option. ADV Advance (skip steps) feature enabled Display Interpretations NO ADV Advance feature disabled WET CL Wet clean function for Auxiliary 1 output (1/2 wash speed) and Auxiliary 2 output (recirculation pump) enabled (see “2DRAIN.”) NO WCL Wet clean function for Auxiliary 1 and 2 disabled (Auxiliary 1 and 2 are timed outputs.) S BAL “Short” balance routine–active only if inverter drive load balance sensing is utilized. L BAL “Long” balance routine–active only if AC inverter drive load balance sensing is utilized. DRTEMP Temperature is above 160°F in drain to reuse tank A or B step. BAL DR* (flashing at the end of cycle) Cycle aborted due to extreme out-ofbalance condition or door is unstable. Table 1 * Design U6 and greater models Table 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232201 Operation Operational Keypad The control includes sixteen keypads. Refer to Figure 6. These functions are available to the operator and are intended to control operation of the washer- extractor. Refer to Table 2. Operational Keypad Keypad Description Numbers 0–9 Press to select cycle number. Display Temp* Press and hold. Display will show and update sump temperature in degrees Fahrenheit or Centigrade. Advance Press to cause computer to skip to the next step in the cycle. The computer will not advance past drain step. (The Advance keypad is enabled at the factory and can be disabled at the laundry site.) Stop Press to immediately abort the cycle and initiate the Stop Routine. Start Press to start selected cycle or to restart a step following a “FILL” or “EMTY” alarm. See Error Recovery Routine in this section of the manual. Manual See Manual Mode Control Feature at the end of this section. Table 2 * If cycle in a spin coast delay, display shows speed of basket. F232201 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Operation 18 F232201 Located to the left of the control keypad are 20 LED indicator lights for the control outputs. During the time that a cycle is running, one or more of these lights will be on to indicate steps in use. Refer to Figure 6. Figure 6 MC008G 1 Out-of-Balance Indicator 4 High Level Fill Indicator 2 Door Lock Switch 5 Medium Level Fill Indicator 3 Program Mode 6 Low Level Fill Indicator 1 2 3 4 5 6 Operation P...