valutazioni - 3, GPA: 5
(
)
)
|
Facilità d'uso
495P3 Hub and Seal Kit Kit Consists of: 1 --27125 Gasket (Washtub) 1 --27184 Gasket (Outlet Tub Cover) 1 --27615P Sealant 1 --29728 Spline Insert 1 --Hub and Seal Assembly 1 --442P3 Drive Bell Seal Kit 1 --12-89-75 Instructions _ _,WARNING To reduce the risk of electric shock or injury to persons, disconnect washer power cord before servicing the washer. If water is present in the washtub, spin and pump out before attempting to remove the drive bell. 1. Refer to the appropriate service manual and remove the washtub and lint filter. 2. Remove the drive bell by following the instructions supplied in the No. 442P3 Drive Bell Seal Kit. IMPORTANT: We recommend that both the seal seat and the seal head be replaced together. DO NOT replace only one of the two seals. 3. Remove the seal head from the hub, 4. Remove the large hex nut, Figure 1, using No. 237P4 Hex Wrench, 5. Remove the spline insert from the transmission tube and discard the old spline insert. IMPORTANT: Use a new spline insert each time the hex nut is removed. DO NOT reuse the old insert as the hex nut may loosen during operation. 6. Remove hub from splines on transmission tube. NOTE: It may be necessary to use a gear puller to remove hub. 7. Remove the old water seal from the outer tub. IMPORTANT: Use caution when removing old seal so as not to damage the tub flange or porcelain. TO INSTALL NO. 495P3 HUB AND SEAL KIT IMPORTANT: Be sure the inner surface of the tub flange is clean of all foreign material before installing the new seal. 8. Apply a small amount of No. 27615P Sealant (supplied in kit) around the outer surface of the tub flange, Figure 2. IMPORTANT: DO NOT allow sealant to get in contact with the flinger, Figure 2, as this could prevent the flinger from keeping moisture out of the upper bearing. HEX NUT TRANSMISSION OUTPUT SHAFT HUB ASSEMBLY Figure 1 OUTER TUB FLANGE APPLY BEAD OF NO. 27615P Figure 2 Form No. 12-89-75 STAINLESS STEEL WATER SLEEVE BRONZE PORTION SEAL OF SEAL LUBRICATE LUBRICATE PRESS HERE TO FLUSH GARTER GARTER SPRING SPRING APPLY BEAD OF NO. 27615P INSERT SLEEVE APPLY BEAD OF SEALANT HERE (Step "12") FROM Bo'n'OM SIDE OF SEAL NO, 27615P SEALANT HERE (_ep "12") Figure 3 9. Apply a light film of non-staining petroleum jelly (such as Vaseline ®) to the bronze portion of the water seal and to the outer surface of the stainless steel sleeve, Figure 3. IMPORTANT: Do not over lubricate! 10. Insert the stainless steel sleeve into the water seal from the bottom side of the seal, Figure 3, until the sleeve is flush with the bronze portion of the seal. 11. Leave the garter spring on the seal. Place the new seal over the outer flange (with the seal lip on outside of tub flange). Then press the seal into the tub flange opening using moderate finger pressure. 12. Carefully apply a small amount of No. 27615P Sealant (supplied in kit) around the outer edge of seal and tub. (The area located just below the garter spring, Figure 3.) IMPORTANT: Do not allow sealant to get in contact with the sealing surface of the water seal as it will cause a water leak. 13. Lubricate the inner splines of the new hub assembly (supplied in kit) with No. 27604P Anti-Seize compound, 14. Carefully place the new hub assembly on the splined transmission tube. IMPORTANT: Firmly push hub down against the outer tub seal and hold in this position. 15. While holdirig the hub down. place the spline insert onto the transmission tube until it bottoms against the hub. Then place the hex nut on the transmission tube (with the larger inside bevel on the nut toward the spline insert), then tighten the nut. IMPORTANT: Torque the hex nut down between 40 to 70 foot pounds (54.23 to 94.91 N-m). If torque wrench is not available, tap hex wrench with a hammer until hub turns or until nut will no longer tighten. NOTE: If a lint filter was originally used between the washtub and hub, then the lint filter must be used again when installing the washtub. Then continue on with step 16. If a gasket was originally used between the washtub and hub, then use the new gasket (supplied in kit) and install the gasket as follows: a, Apply a small amount of non-staining petroleum jelly (such as Vaseline ®) to each of tile sealing surfaces where washtub gasket will contact hub and the bottom of the washtub. b. Carefully place the new washtub gasket, No. 27125, (supplied in kit) on hub. 2 CLIPS (8) LEFT FRONT NOTCH CLIP HOLE )UTER TUB COVER TUB Figure 4 NOTE: Be sure holes in gasket are aligned with bolt holes in hub and that all traces of the old gasket are removed from the bottom of the washtub. 16. Install washtub by grasping the top flange of the washtub and carefully lower washtub down onto the lint filter or gasket and hub. IMPORTANT: Before setting tub into place, be sure bolt holes in washtub line up with holes in the lint filter or gasket and hub. 17. Secure washtub to hub using four cap screws previously removed. IMPORTANT: Porcelain Washtub Models --Use care when tightening cap screws...