valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
If you sell the appliance, pass it on to someone else, move house and leave it behind, make sure that you provide this book so that the new owner can become familiar with the appliance and safety warnings. Please remember your new appliance is a complex piece of equipment. DIY repairs or unqualified and untrained service people may put you in danger, could damage the appliance and might mean you lose cover under Creda’s Part Guarantee. Dear Customer, Congratulations on the purchase of your new ‘Creda’ appliance. We recommend for your own safety and to get the best possible results from your machine that you read through this handbook thoroughly before using your appliance for the first time. . Transit Brackets MUST be removed before using the appliance. . DO NOT plug in and switch on at the mains until installation is complete. Contents Electrical requirements Recycling & Disposal Information Choosing a Location Adjusting the Feet 2 Installation Instructions Transit Bracket Removal Connecting to the Water Supply Removing the Polystyrene Pyramid Connecting to a Drainage System 3-4 Getting to Know your Machine Wash Load Guides Interlocking Door System Washcare tips 5 A Typical Wash Programme 6 Controls 7 Choosing A Wash Programme 8 Optional Wash Features 9 Dispenser Drawer 10-11 Care and Cleaning 12 Maintenance Wash Regular Checks and Stain Removal 13 Something wrong with your appliance 14 Service Cover 15 Key Contact Numbers Back page Electrical Requirements This appliance should be connected to the mains supply via a suitable switched socket in an accessible position. WARNING: This appliance must be earthed. FUSES Your appliance comes fitted with a plug and a 13A fuse. If you need to replace the fuse, only those rated at 13A and ASTA approved to BS1362 should be used. To change fuse, lift holder to vertical position and lift fuse out. To replace, insert fuse and push fuse holder down into locked position. Correct replacement is identified by colour coding, or marking on base of plug. WARNING: Do not use plug unless fuse holder is in locked position. CHANGING THE PLUG Cut off and dispose of the supplied 13A ASTA plug if it does not fit your socket. Green and yellow Cord clamp approved (Earth) wire to the fuse to WARNING: To avoid a shock haz terminal marked BS1362. ard do not insert this plug into a ‘E’ or with the socket anywhere else. symbol , Brown (Live) or coloured IMPORTANT: WIRES IN THE MAINS wire to the green and terminal LEAD ARE COLOURED IN yellow. marked ‘L’ or ACCORDANCE WITH THE coloured to the terminal marked Blue (Neutral) wire red. FOLLOWING CODE: ‘N’ or coloured black. Green/Yellow– Earth Blue – Neutral Brown – Live If you change the plug, the colour of wires in the mains lead may not correspond with the colour of the markings identifying terminals in the plug. You should therefore wire it as shown (see illustration). If the mains lead needs to be replaced at any time, it should be replaced by a special lead obtainable from your local authorised Creda Service Centre. A charge will be made if you have damaged the existing lead or require a longer one. It is strongly advised that this work is carried out by a qualified electrician. CE marking certifies that this appliance complies with requirements laid down in EEC Directive 89:336 (Electromagnetic compatibility) and subsequent modifications and Low Voltage Directive 73/23/EEC. Positioning & Adjusting the feet Choosing the position of your appliance will influence its performance. . Position where possible on a solid floor. Some vibration may occur with a wooden floor. . Take care with vinyl floor coverings. The weight of the appliance may cause indentations in some vinyl floor coverings. . For your safety and to comply with IEE regulations, you should not install your appliance in a bath or shower room. Seek professional advice if you wish to do so. . Ensure sufficient space is allowed for the appliance. Dimensions should be a minimum of:- 600mm Wide (235/8”), 600mm Deep (235/8”) and 900mm High (351/2”). . Ensure the electrical socket and water taps are easily accessible and that the water supply can be isolated if necessary. Your appliance may become noisy or move about the floor if it is not stabilised. To adjust your appliance it must be in an upright position, then :. Release locking rings on the two front feet. . Screw feet in or out until the appliance is standing firm and level. . Ensure all feet are in firm contact with the floor. . Tighten the locking rings on the front feet. Recycling & Disposal Information As part of Creda’s continued commitment to helping the environment, Creda may use quality recycled components to keep down customer costs and minimise material wastage. Please dispose of packaging and old appliances carefully. To minimise risk of injury to children, remove the door, plug and cut mains cable off flush with the appliance. Dispose of seperately to ensure that the appliance can no longer be plugged into a mains socke...
Questo manuale è adatto anche per i modelli :Lavatrici - W120FW (266.76 kb)
Lavatrici - W120VW (266.76 kb)