valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Then tighten the lock nuts. Lock nut Condensed water Install the dryer so the condensed water will continuously flow into a drain or sink. To do this, follow the instructions below: 1. Disconnect the short hose (1) from the blue connection. (It’s okay to let the hose hang down.) 2. Connect the rubber hose supplied with the dryer to the blue nipple (2). 3. Run the hose to a drain or sink, as illustrated (3). Note The drain hose must not be more than 40” above the floor. 1 3 2 3 Maximum height 40" Electrical installation The machine should only be connected to a grounded wall socket. Warning! This appliance must be properly grounded. Refer to the “Important Safety Instructions” for grounding instructions. The power supply cord must be grounded. If the machine is to be used in a wet area, the supply must be protected by a residual current device. Connection to a permanently wired supply point must be made only by a qualified electrician. As supplied: Single-phase, 230 V, 60 Hz, 1950W heater rating 30 A circuit required Warning! The receptacle on the rear of the machine is designed to accommodate ASKO washers ONLY (rated 208–240 V.) To use this receptacle, you must use the ready-fitted plug supplied with the washing machine or an equivalent. ASKO washers rated 208–240 V have two internal fuses of 15 A each. Remove cover to access terminal box. (Requires a 20-Torx screwdriver.) Note In Canada, the dryer is delivered ready-fitted with a four-prong plug intended for connection to a single-phase supply. 26 Customer Care Center 1-800-898-1879 Installation instructions Connecting a 3-wire Power Cord Warning! Before starting this procedure, be sure the power is turned off at the breaker/fuse box. Power Supply Cord You will need a 3-wire power supply cord with three No. 10 copper wires and a matching 3- wire receptacle of NEMA Type 10-30R, as illustrated below: To connect a 3-wire power cord to the dryer, follow the steps below. Ground Ground (center) Note The numbers in the illustration below correlate to the step numbers. 1. Turn the power off at the breaker or fuse box. 2. Remove terminal block cover. 3. Use the strain relief attached below the terminal block opening. 4. Loosen or remove center terminal block screw. 4 6 5 7 5. Connect ground (center) wire of power supply cord to the center, silver-colored terminal screw. Tighten screw. 6. Connect the other wires to outer screws. 7. Tighten the strain relief screws. 8. Replace terminal box cover on back of dryer. 9. Plug dryer into wall receptacle. 10.Turn power on at breaker/fuse box. Connecting a 4-wire Power Cord Warning! Before starting this procedure, be sure the power is turned off at the breaker/fuse box. Power Supply Cord You will need a 4-wire power supply cord with four No. 10 copper wires and a matching 4- wire receptacle of NEMA Type 14-30R, as illustrated below. The fourth wire must be identified with a green cover and the ground conductor by a white cover. To connect a 4-wire power cord to the dryer, follow the steps below. Note The numbers in the illustration below correlate to the step numbers. 1. Turn the power off at the breaker/fuse box. 2. Remove terminal block cover. 3. Use the strain relief attached below the terminal block opening. 4. Remove center terminal block screw. Customer Care Center 27 1-800-898-1879 Installation instructions 9 8 7 6 5 4 5. Remove ground wire (green with yellow stripes) from external ground connector screw. Fasten under center, silver-colored terminal block screw. 6. Connect ground (green) wire of cord to external ground conductor screw. 7. Connect ground (white) wire of cord under center screw of terminal block. 8. Connect the other wires to outer screws. 9. Tighten the strain relief screws. 10.Replace terminal box cover on back of dryer. 11.Plug dryer into wall receptacle. 12.Turn power on at breaker/fuse box. 28 Customer Care Center 1-800-898-1879 Installation instructions 1. Hinge pins (top and bottom) 4. Lock hook 2. Cover washer 5. Hinges (left + right side) Plastic plugs (on the upper 6. Toe kick and lower edges) 3. Customer Care Center 29 1-800-898-1879 Reversing the door You can choose whether the door is hung on the right or the left. Follow these instructions: 1. Remove the Toe kick. 2. Unscrew the 2 screws on the hinges. 3. Lift the door up and remove it. Support the door while doing this. 4. Remove both door pins (top and bottom). Fit them on the opposite side of the door. Refit the hinges. 5. Undo and remove the lock hook (lift up and pull out) and the cover washer from the door and the machine. Fit the hook and the washer on the other side. 6. Move the plastic plugs on the upper and lower edges of the door. Use a flat screwdriver to remove the plugs. 7. Refit the door by loosening the hinge screws slightly, affixing the door, and closing it. Retighten the hinges. Replace the Toe kick. 30 Customer Care Center 1-800-898-1879 Rev...