valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
outward 4. Install 2 screws through each rear bracket into aligning pedestal holes. Dryer cabinet (style 2) with 2 indents on side and 4 inch knockout for side venting. 5.8 cu ft DRYER (STYLE 2) INSTRUCTIONS (GREEN KIT) NO spacers under front brackets. “B” tab front slot - EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the dryer. TIP DOWN SLIDE BACK ENGAGE REAR TABS • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • GREEN KIT • 6 • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • - EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the washer. C4) Attaching washer mounting hardware 3.1 cu ft WASHER INSTRUCTIONS (WHITE KIT) D4) Mounting washer E4) Installing or re-installing washer 1. Use the following instructions for mounting this type of washer to the pedestal: 1. Using two or more persons, slightly tip the washer back and lift it onto the pedestal. Still tipped, slide the washer back against the rear brackets and gently set down the front so the appliance is between the front and rear brackets. 2. Remove lower service access panel. 3. Remove 2 lower screws from backsheet of washer. Save screws to reinstall later. 4. Attach each front clip to outer-most set of holes with 2 screws. 2. Adjust the appliance side-to-side to align its mounting holes with the pedestal’s bracket holes. 3. Reinstall backsheet screws removed earlier through each rear bracket into the base of the washer. 4. Reinstall the lower service access panel. 5. Reinstall the 2 screws removed earlier through the outer hole of each front bracket into the base of the washer. 1. Slide appliance/pedestal into place. 2. Check for levelness and rock all four (4) legs again. Repeat until level and solid. 3. Refer to Washer Installation Instructions for complete details on installing water, drain, or electrical. SLIDE BACK TIP DOWN middle slot outward 5. Insert “A” tab of each rear bracket into the middle slots on rear of pedestal. Orient bracket outward for washer mounting. “A” tab Remove 2 screws from service access below front panel. Remove 2 screws from washer backsheet. 6. Install 2 screws through each rear bracket into aligning pedestal holes. 7 C5) Attaching dryer (style 3) mounting hardware D5) Mounting dryer (style 3) E5) Installing or re-installing dryer (style 3) 1. Using two or more persons, slightly tip the dryer back and lift it onto the pedestal. Still tipped, slide the dryer back against the rear brackets so tabs on rear brackets engage the slots on the back of the dryer. Gently set down the front so the appliance is between the front and rear brackets. 2. Adjust the appliance side-to-side to align its mounting holes with the pedestal’s bracket holes. 3. Install a screw through the inner hole of each front bracket into the base of the dryer. 1. Slide appliance/pedestal into place. 2. Check for levelness and rock all four (4) legs again. Repeat until level and solid. 3. Refer to Dryer Installation Instructions for complete details on installing electrical, gas, or exhaust venting. 5.7 cu ft DRYER (STYLE 3) INSTRUCTIONS (WHITE KIT) - EXCESSIVE WEIGHT HAZARD - To avoid back or other injury, have more than one person move or lift the dryer. TIP DOWN SLIDE BACK ENGAGE REAR TABS 4. Reinstall the plastic hole plugs in front panel. • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • WHITE KIT • 1. Use the following instructions for mounting this type of dryer to the pedestal: 2. Remove all 4 adjustable leveling legs from the appliance base and save for future use. 3. Remove 2 plastic hole plugs toward bottom of front panel. 4. Attach each front clip to outer-most set of holes with 2 screws. 5. Insert “B” tab of each rear bracket into the front slots on rear of pedestal. Orient bracket outward for “style 3” dryer mounting. outward 6. Install 2 screws through each rear bracket into aligning pedestal holes. Dryer cabinet (style 3) with 2 indents on side and 4 inch knockout for side venting. Dryer console (style 3) has mechanical style timer. Remove 2 plastic hole plugs toward bottom of front panel. Remove 4 plastic leveling legs. “B” tab front slot INSTRUCTIONS DE PREPARATION 8 Laissez environ 12,7 cm (5 po) derriere le socle pour laisser un espace libre a l’arriere de la laveuse ou de la secheuse par rapport au mur. Prevoyez de l’espace supplementaire si la ventilation de la secheuse doit etre effectuee vers le haut ou vers le bas. Si les contre-ecrous ne sont pas retires sur les appareils munis de pieds en metal, les trous de montage de l’appareil ne s’aligneront pas sur ceux des supports. En raison du centre de gravite plus eleve des electromenagers sur socles, il est normal qu’il y ait un balancement de va-et-vient lateral durant le fonctionnement. Il est possible de reduire la vibration en s’assurant que l’electromenager est installe correctement, ce qui comprend une mise a niveau solide de l’appareil sur ses quatre ...
Questo manuale è adatto anche per i modelli :Lavatrici - FNDP15B (2.93 mb)