valutazioni - 5, GPA: 4.8
(
)
)
|
Foto e specifiche Candy CY 124 TXT |
Facilità d'uso
T) Always ensure that the door locked indicator neon has switched itself off before opening the door. By doing so the machine is allowed to cool down before the laundry is handled. U) Always ensure that the base panel is fitted to the machine. Quick Start Washing - Press the button inside the door handle to open the door. - Select laundry and put it in the machine. - Close the door. - Put detergent in the dispenser compartments, compartment I for pre wash and compartment II for all other programmes. - Select programme by turning the programme knob (Your desired programme may be seen on the display). - Select any function buttons required and then press the Start/Pause button (START/PAUZE). - There may be a short time delay from pressing the start/pause bottom to the start of theprogramme, while the machine senses the water required and sets the parameters for the programme. When the programme has finished - The display will read “DOOR LOCKED-WAIT TO OPEN”. - After 2 minutes the display will read “PROGRAM ENDED - DOOR OPEN”. - Switch off the machine by turning the control knob to the off position. - Open the door and remove the laundry. Disconnect the plug from the mains power supply and turn off the water supply after every use. 41 Useful advice for users Tips on using your domestic appliance in the most environmentally-friendly and economical way Do a full load in your washing machine To prevent any possible waste of energy, water or detergent we recommend that you put a full load in your washing machine, not exceed the maximum load size. Save up to 50% energy by washing a full load instead of 2 half loads. When is prewashing really needed? Only with particularly dirty loads! Energy savings of 5 to 15% are made by not selecting the prewash option for normally soiled laundry. Which wash temperature should you choose? Using stain removers before machine washing reduces the need to wash at temperatures over 60°C. Energy savings of up to 50% can be made by using a 60°C wash temperature. 42 A quick guide around your Candy Infotext menu: Connect product up to the electric / water supplies and drainage (see pag. 70). Select any wash programme. After a short time a message will be displayed: WELCOME 0.00 12 COTTON WHITE 90 HEAVY SOIL accurate time can be reset later this is displayed if prog. 1 is selected Prior to entering the Infotext pre set, remember time is limited while you decide on your options (30 sec. / section). If you run out of time start from this point again. Hold down at the same time the (T°c) and ( ) buttons for 5 sec. until screen changes to: ADOPT LANGUAGE ENGLISH Press ( T°C ) (This confirm and enters an option) Your washing machine is automatically set to English. Press ( T°C SET TIME MODE ABSOLUTE to change hours press the (@) ) until correct to change mins press the ( (^) ) until correct if RELATIVE is displayed press | (This changes a menu option) Press (rc; 43 if NO is displayed press | if NO is displayed press the | always select NO, if YES press | if NO is displayed press the | 12 COTTON WHITE HEAVY SOIL 90 reverts back to the wash programme selected You are now able to select any wash programme. You can if you wish also set a delay start. Where more detailed information is required refer to the relevant section from the following pages. 44 When using your new Infotext for the first time This machine will operate prior to programming the Infotext set up. However, this machine has Start Delay and Programme End functions and for these functions to work efficiently the Infotext set must be programmed. This is a simple operation and special care has been taken during manufacture to ensure that the user can operate this machine simply and effectively. Programming the machine Infotext needs to be programmed so that the correct clock setting, language and personal requirements are set. When the machine is turned on and the programme dial is moved away from the “off” position to the programme selections a welcome message will appear. WELCOME 00.00 This message is displayed for a short time while the machine recognises which programme has been selected. When the machine is ready, the programme details will appear on the display and from here you may now beging programming the machine. Example 12 COTTON WHITE HEAVY SOIL 90 Enter the Menu Prior to entering the Infotext menu please note you have 30 seconds per operation to make your selection. Should you run out of time the display will return to the start screen, and you simply have to re-enter the Infotext menu at continue with the programming. From this stage the menu can be programmed. Hold down the (T°C) and the ( ||)) buttons together for 5 seconds or until the beep sounds. The menu options can be changed by pressing the ( @)) button. To confirm and enter an option press the (T°C) button. Setting the language Your washing machine is automatically set to Engli...