Log:
valutazioni - 4, GPA: 3.8 ( )

Istruzioni per l'uso AEG, Modello L 60660 FL

Produttore : AEG
File Size : 1.39 mb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


hose has no damages. The filters in the water in-Clean the filters. Refer to 'Care let hose is blocked . and cleaning'. The water tap is blocked or is furred with lime- Clean the water tap. scale. The connection of the Make sure that the connection is water inlet hose is not correct. correct. The water pressure is too low. Contact your local water authority. The appliance The water drain hose is Make sure that the water drain does not drain the damaged. hose has no damages. water. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and clean- ing'. The connection of the water drain hose is not correct. Make sure that the connection is correct. A washing programme without the drain phase is set. Set the drain programme. The function Rinse & Hold is on. Set the drain programme. The appliance door is open or not closed correct- ly. Close the door correctly. ENGLISH 27 Problem Possible cause Possible solution The spin phase The spin phase is off. Set the spin programme. does not operate. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and clean- ing'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The programme does not start. The mains plug is not connected in the mains Put in the mains plug. socket. Blow out fuse in the household fuse box. Replace the fuse. You did not press button 4 . Press button 4 . The delay start is set. To start immediately the pro- gramme, cancel the delay start. The Child Lock function is activated. Deactivate the Child Lock func- tion. There is water on Leakages from the cou-Make sure that the couplings are the floor. plings of the water ho-tight. ses. Leakages from the drain pump. Make sure that the drain pump filter is tight. The water drain hose is damaged. Make sure that the water inlet hose has no damages. You cannot open The washing programme Let the washing programme end. the appliance is in operation. door. There is water in the Set the drain or the spin pro- drum. gramme. The appliance Incorrect level of the ap-Adjust the level of the appliance. makes an unusual pliance. Refer to 'Installation'. noise. You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Instal- lation'. The load is very small. Add more laundry in the drum. The appliance fills with water and drain immediately. The end of the drain hose is too low. Make sure that the drain hose is in the correct position. The washing results are not satis- The detergent you used was not sufficient or cor- Increase the detergent quantity or use a different one. factory. rect. Problem Possible cause Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the cor- rect temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. If the display shows other alarm codes, The programme continues from the contact the service centre. point of interruption. If the problem occurs again, contact the service centre. ENGLISH 29 INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door and remove all the items from the drum. 6. Put the front piece on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 1 2 7. Remove the polystyrene protection from the bottom. 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. ENGLISH 31 12. Replace the plastic spacers with the plastic caps. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures. Store it at room temperature for 24 hours before using for the first time. POSITIONING AND LEVELLING x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. THE INLET HOSE 35O35O35O45O45O45O • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the co...

Questo manuale è adatto anche per i modelli :
Lavatrici - L 60460 FL (1.39 mb)
Lavatrici - L 60468 FL (1.39 mb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie