valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
If after all checks, the problem persists, contact your local AEG Service Force Centre. Problem Possible cause Solution The ON/OFF button Depress the button. has not been depressed. The main electrical fuse Replace the fuse. has blown. The door is not properly Close the door; the click The machine does not work closed (E20). of the lock should be heard. The plug is not connected. Insert the plug. The START button has not Press the button. been pressed. The DELAY START Check the selected delay on option has been selected. the display. Something not working? Problem The machine does not fill The machine fills then empties immediately The machine does not empty and/or does not spin There is water on the floor Possible cause Solution The water tap is closed (E00). Open the water tap. The water inlet hose is Check the whole length of the squashed or kinked (E00). hose and remove the kink. The small filter of the water Clean the filter. inlet hose is clogged (E00). The door is not properly closed (E20). The end of the drain hose is too low. The drain hose is squashed or kinked (E10). Close the door. Place the hose at the right height (see Installation section). Check the whole length of the hose and remove the kink. The drain filter or the Clean the filter or check drain hose are clogged (E10). the hose. The RINSE HOLD option Empty out the water by (stop with water in drum) pressing the START button has been selected. or selecting the PUMP OUT programme. The laundry is not evenly Redistribute the laundry distributed inside the drum. manually in the drum. Too much detergent has Measure detergent been used. according to the manufacturer’s instructions. An unsuitable detergent Use a suitable washing has been used that machine detergent. creates too much foam. One of the connectors on Check that the hose is the water inlet hose is firmly screwed on at both leaking. ends. The drain filter has not Fully screw the filter into been properly screwed on place. after cleaning. Problem The machine vibrates or is noisy The door will not open Something not working? Possible cause Solution The transit bolts have Check that the machine not been removed. has been unpacked as described in the Installation section. The feet have not been Carefully level the machine. adjusted. There is little laundry in the drum. The programme is still running. Correct operation of the machine is not affected. Wait until the end of the programme before opening the door. The door lock has not yet Wait about 2 minutes for released. the door lock to release. The water level is above the Before opening the door, bottom edge of the door. the water must be emptied out. The machine is heating the Wait until the end of the water. heating phase. Something not working? Problem Spinning starts late or the machine does not spin The machine will not dry or the laundry is not dry enough Possible cause The unbalance detection device that prevents excessive vibration during spinning has cut in. The water tap is not open (E00). Solution If the laundry is not evenly distributed inside the drum at the beginning of the spin cycle, the machine detects this and tries to redistribute it more evenly by means of a few drum rotations. Only when the laundry is more evenly distributed will the spin cycle be performed, at a lower speed, if the laundry is not evenly distributed. If, after about 15 minutes, the laundry is still tangled, the machine will not spin. Therefore, if the laundry is still wet at the end of the cycle, it is advisable to redistribute it manually inside the drum and to select the spin programme again. Open the water tap. The drain filter is clogged. Clean the filter. The drying time has not Select the drying time. been selected. An appropriate drying time Select the appropriate has not been chosen. drying time suitable for the required degree of drying, according to the type of fabric (cottons or synthetics). There is too much laundry Reduce the load. inside the appliance. Something not working? Unsatisfactory washing results If the laundry looks grey and lime scale is found in the drum • Too little detergent has been used. • An unsuitable detergent has been used. • Stubborn stains have not been treated prior to washing. • The programme/temperature has not been correctly selected. If grey stains remain on the laundry • Laundry stained with ointments, grease or oil has been washed with an insufficient amount of detergent. • The temperature selected for the wash programme was too low. • Fabric softener - especially the concentrated type - has come into direct contact with the laundry. Wash these stains immediately and pour fabric softener carefully. Foam is still visible even after the last rinse • Modern detergents often produce foam, even in the last rinse. However the laundry has been completely rinsed. White residue is left on the laundry • This is due to insoluble components in modern detergents and is therefore not the result of insufficient rinsing. Sh...