valutazioni - 5, GPA: 3.4
(
)
)
|
Foto e specifiche AEG L 71260 SL |
Facilità d'uso
Adjust manually the items in the tub and start the spin phase again. The programme The mains plug is not Put in the mains plug. does not start. connected in the mains socket. You did not press button 4 . Press button 4 . The delay start is set. To start immediately the pro- gramme, cancel the delay start. The Child Lock function is activated. Deactivate the Child Lock func- tion. Blow out fuse in the Replace the fuse. household fuse box. There is water on Leakages from the cou-Make sure that the couplings are the floor. plings of the water ho-tight. ses. Leakages from the drain pump. Make sure that the drain pump filter is tight. The water drain hose is damaged. Make sure that the water inlet hose has no damages. You cannot open The washing programme Let the washing programme end. the appliance is in operation. door. There is water in the Set the drain or the spin pro- drum. gramme. The appliance Incorrect level of the ap-Adjust the level of the appliance. makes an unusual pliance. Refer to 'Installation'. noise. You did not remove the packaging and/or the transit bolts. Remove the packaging and/or the transit bolts. Refer to 'Instal- lation'. The load is very small. Add more laundry in the drum. ENGLISH 29 Problem Possible cause Possible solution The appliance fills with water and drain immediately. The end of the drain hose is too low. Make sure that the drain hose is in the correct position. The washing results are not satis- The detergent you used was not sufficient or cor- Increase the detergent quantity or use a different one. factory. rect. You did not remove the stubborn stains before Use special products to remove the stubborn stains. you wash the laundry. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. If the display shows other alarm codes, The programme continues from the contact the service centre. point of interruption. If the problem occurs again, contact the service centre. INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. Remove the cardboard top. 3. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door and remove all the items from the drum. ENGLISH 31 1 2 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Pull up the appliance in vertical position. 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag. – We recommend that you keep the packaging and the transit bolts for when you move the appliance. – If the appliance is delivered in the winter months when there are minus temperatures. Store it at room temperature for 24 hours before using for the first time. POSITIONING AND LEVELLING x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. A correct adjustment of the appliance level prevents the vibration, noise and the movement of the appliance when in operation. ENGLISH 33 • The appliance must be level and stable. CAUTION! Do not put cardboard, wood or equivalent materials below the appliance feet to adjust the level. THE INLET HOSE 20O20O20O45O45O45O • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device A The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault . If this occur, close the water tap and contact the service centre to replace the hose. WATER DRAINAGE There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. 34 ENGLISH 35 Without the plastic hose guide. •To a sink spigot. ...
Questo manuale è adatto anche per i modelli :Lavatrici - L 71060 SL (1.74 mb)