valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
• The programme/temperature has not been correctly selected. If grey stains remain on the laundry • Laundry stained with ointments, grease or oil has been washed with an insufficient amount of detergent. • The temperature selected for the wash programme was too low. • Fabric softener - especially the concentrated type - has come into direct contact with the laundry. Wash these stains immediately and pour fabric softener carefully. Foam is still visible even after the last rinse • Modern detergents often produce foam, even in the last rinse. However the laundry has been completely rinsed. White residue is left on the laundry • This is due to insoluble components in modern detergents and is therefore not the result of insufficient rinsing. Shake or brush the laundry. In future, it may be better to turn garments inside out before washing them. Check the choice of detergent; try using liquid detergents. Technical data Height x Width x Depth 85x60x60 cm Depth with door opened 101,5 cm Height adjustment ± 13 mm approx. Load (depending on programme) 6 kg Use domestic Drum speed during washing max. 55 rpm Drum speed during spinning 1400/1200/900/700 rpm Water pressure 0,05-0,8 MPa This appliance complies with the following EC directives: -73/23/EEC of 19.2.1973 “Low voltage directive”, including directive 93 / 68 / EEC -89/336/EEC of 3.5.1989 “Electromagnetic Compatibility Directive”. Service In the section “Something not working?” some problems that can be solved by yourself are listed. Read this section in the event of problems. If you are not able to find a solution, contact the Service centre. In all cases, explain your problem carefully, in order to facilitate troubleshooting: the engineer will be able to decide whether a service call is necessary. Take note of the serial number (Ser. No.) and the product number (Prod. No.) indicated on the rating plate. Ser. No. . . . . . . . . . . . . . . . . . . . . . . . Prod. No. . . . . . . . . . . . . . . . . . . . . . . Furthermore, try to specify, as precisely as possible: ! "# -The symptoms of the fault -When the fault occurs -The alarm code displayed When can a service visit be charged during the guarantee period? -when it should have been possible to solve the problem by yourself, with the help of the troubleshooting chart (see section “Something not working?”) -when the engineer has to come out several times because he has not been given all the relevant information he needs and so, for example, has to fetch spare parts. Repeated trips can be avoided if you prepare your call to the Service centre as described above. Instructions for installation and electrical connection Safety instructions for the installer • This appliance is heavy, care should be taken when moving it. • When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the retailer. • All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protective transit devices are not completely removed. Refer to the relevant paragraph. • Any electrical work required to install this appliance must be carried out by a qualified electrician. • Any plumbing work required to install this appliance must be carried out by a qualified plumber. • After having installed the machine, check that it is not standing on its electrical supply cable. • If the appliance is placed on a carpeted floor, ensure that air can circulate freely between the adjustable feet and the floor. • The installation should comply with local water authority and building regulations requirements. • Should the appliance power supply cable need to be replaced, this should be carried out by our Service Force Centre. Dimensions of the appliance Front view and side view Rear view 45 $ $ Installation Unpacking All transit bolts and packing must be removed before using the appliance. Using the supplied spanner, unscrew and remove the 2 rear bottom screws. Slide out the 2 plastic pins. Lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor. Remove the polystyrene block from the bottom of the machine and release the two plastic bags. Carefully slide out the left-hand bag removing it towards the right and then downwards. Slide out the right- hand bag removing it towards the left and then upwards. The bottom cover plate, which can be found inside the machine with the instruction book, will now need to be fitted. Hook the bottom of the plate «A», into position first. Then push the other end of the plate into position. Important! You can find more detailed instructions regarding the bottom cover assemblig in its relative bag. Installation Set the machine upright and remove the remaining rear screw. Slide out the relevant pin. Plug the open holes with the plugs which you will f...