valutazioni - , GPA:
(
)
)
Produttore : Hotpoint
File Size : 1.43 mb
File Nome : HBWD42.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
ALWAYS SWITCH ELECTRICITY OFF AT THE SOCKET AND REMOVE PLUG AFTER USE. WARNING: WHEN SWITCHING ELECTRICITY OR MACHINE ON OR OFF, PLEASE ENSURE THAT YOUR HANDS ARE DRY. 6 10. Remove the plastic blanking plate (f) (Fig. 3).. Insert a small coin into the slot provided on the blanking plate (f). Grip the coin with fingers or pliers and rotate plate to release. Remove the plate and replace where the catch was previously removed. Secure by rotating in the opposite direction to removal. 11. Turn the catch (e) 180° and place in position where the blanking plate (F) was removed. Grip the catch carefully, with pliers and rotate in position to secure. 12. Place the lower hinge in position, locating the correct position. Secure with hinge screws. 13. Carefully hang the door onto the lower hinge. Inserting the Decor Panel Decor panels are available from most kitchen manufacturers. Decor Panel Sizes: Door - Height 526mm, Width 587mm Thickness - 4mm maximum or up to 8mm if the edge is thinned down to 4mm for a width of 3.5mm as shown in Fig. 4. 3.5mm Fig.4 -~i-U t 4mm | Y "T Decor Panel Fig.3 DECOR DOOR Locate the top hinge into the retaining hole on the top of the door, Carefully locate the top hinge into position. (Ensure that the screws and screwdriver are close at hand.) Screw the top hinge into position. The decor door should now close. To fit decor panels first make sure that they are cut to correct size. 1. Remove the decor door by unscrewing the top door hinge. 2. Remove the trim from the top of the decor door. 3. Loosen the screw in the side and base trims. 4. Slide the decor panel into position, from the top, between the trim and front of the decor door. 5. Tighten the screws in the side and base trims. 6. Replace the top trim and fix into position. 7. Rehang the decor door on the bottom hinge and replace the top hinge. 35 Inserting the Decor Door_■ Changing the Decor Door Hin Changing the Decor Door Hinging Changing the Decor Door Hinging WARNING: Switch off the electricity supply to the appliance BEFORE changing the door hinging. Method: 1. Open decor (outer) door. 12. Unscrew and remove blanking plate (a) on the Washer Dryer (Fig. 2). 3. Unscrew and remove catch (c) on Washer Dryer (Fig. 2). Turn 180° and replace where the blanking plate was removed. 4. Screw in blanking plates (a) where catch (c) was removed. 5. Unscrew and remove the two blanking plates (b) (Fig. 2). Retaining the plates and the screws. 6. Unscrew and remove the two decor door hinges (d) (Fig. 2). It is advisable to have another person hold the decor door whilst the hinges are removed. Retain the hinges and screws. 7. Locate and screw in blanking plates (b) into the slots where the door hinges (d) were removed. 8. Place the decor (outer) door on a flat surface, beneath padding to protect the outer surface. 9. Remove the plastic door catch (c) (Fig. 3). Grip the catch carefully, with pliers and rotate the catch to release it. Remove the catch. You will need a: No. 2 Posidrive screwdriver A large pair of pliers A small coin. Fig.1 DECOR DOOR Press top right hand side and door will open Fig. 2 WASHER DRYER 34 How to do a wash only BEFORE THE WASH Turn on hot and cold water Hot water should ideally be at60°C (140°F) and must not be above 70°C (160°F). WARNING: ENSURE HANDS ARE DRY. Sort your laundry See page 16 Make up a load of similar fabrics DO NOTTUMBLE DRY WOOLLENS Press where arrowed to open outer door. Press Door Release button to open inner door Load the machine Do not overload the machine Add detergent and fabric conditioner Seepages 18 and 19 T05" Lockthe Dispenser Drawer Turn the drawer lock in a 90° anti-clockwise direction to horizontal position 7. Switch on the machine Press in the On/Off button See page 22 8. Select relevant Programme and Wash L< \ot/ 1 \ —[l—'/ NORMAL Press in Wash and Spin Selector button until required programme shows in display. Then press Wash button until relevant wash shows in display See pages 22 and 23 Wash & Spin Wash Programmes L_ I 1 7 How To Do a Wash Only 9. Select optional wash features if required RINSE Rinses Rinse Hold Rinses -select Normal, Reduced or Extra-see page 25 Rinse Hold - stops during the final rinse Rinse Hold light will flash. To continue press Rinse Hold button - see page 25 10. Select Delay Hours if required Delay Hours - Delays the time you wish the programme to finish See page 25 11. Lock the On/ Off and Door Release Buttons