valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
If it is the first key pressed in PROGRAM mode, the computer enters SETUP mode. The Stop key can be pressed again to exit SETUP mode and return to PROGRAM mode. Setup Mode SETUP mode allows the selection of degrees Fahrenheit or degrees Celsius for the temperature display. To enter SETUP mode, press the Stop key while the display is showing the temperature in the sump. Once in SETUP mode, use the Up or Down key to change the selected option. Use the Start key to accept the selected option, either “FAr” or “CEL.” Press the Stop key to exit SETUP mode. F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 21 Safety Cycle Count To display the current cycle count, press the Start key while the display is showing the temperature in the sump. The display will show a 2-digit number indicating how many cycles have been run to completion (cycles which were stopped in progress are not counted). Press the Start key to return to PROGRAM mode without resetting the count. Press the Up or Down key to reset the count to zero and return to PROGRAM mode. Cycle Programming To edit an existing cycle or create a new cycle, press the Up key while the display is showing the temperature in the sump. The display will show “CY01.” Press the Up or Down key until the desired cycle number is displayed. Press the Start key to begin editing the selected cycle. All cycle programs (“CY01” – “CY30”) can be customized within a preset program structure. Each cycle program consists of eight program segments. See the table below. Cycle Program Segments Segment Display Segment Display Prewash PrE Fill 3 FIL3 Wash UASH Fill 4 FIL4 Fill 1 FIL1 Fill 5 FIL5 Fill 2 FIL2 Fill 6 FIL6 When modifying a cycle, a time must be entered for each segment. To skip a segment or spin, set the time to “00” and press the Start key. The following table gives the time parameters for each segment and spin, as well as the allowable temperature range. Time And Temperature Parameters Function Minimum Maximum Prewash 2 minutes 30 minutes Wash 2 minutes 20 minutes Fill 1 2 minutes 15 minutes Fill 2 2 minutes 15 minutes Fill 3 2 minutes 15 minutes Fill 4 2 minutes 15 minutes Fill 5 2 minutes 15 minutes Fill 6 2 minutes 15 minutes Intermediate Spin 30 seconds 120 seconds Final Spin 1 minute 10 minutes Temperature 75°F (25°C) 200°F (93°C) Note: Spin times in cycle segments 1 – 8 are entered in seconds (30 to 120), and time for final spin in segment 11 is entered in minutes (1 to 10). 1. Press the Up key until the computer display shows the segment to be edited. Press the Start key. 2. Use the Up or Down key to select the desired segment time. Set this value to zero to skip the segment. Press the Start key. Note: The computer does not count down the remaining cycle time during fills, drains, or prior to first achieving the programmed heat temperature when heating. The computer resumes counting down cycle time once the programmed fill level is reached, when the machine has drained, and after a programmed heat temperature is reached. 22 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232073 Safety 3. Use the Up or Down key to select the desired fill temperature. See the following table for fill options. Fill Temperature Options Display Fill Type CFIL Cold fill HFIL Hot fill bFIL Warm fill 4. Press the Start key. 5. Use the Up or Down key to select the desired fill level. See the following table. Water Level Options Display Fill Level LOLE Low Level HILE High Level 6. Press the Start key. 7. Use the Up or Down key to select the desired supply option. See the table below. 8. Press the Start key. 9. If the machine is equipped with an auxiliary heating system, use the Up or Down key to select the desired segment temperature. To disable auxiliary heat for this segment, set this value to zero. Note: Do not program heat steps for machines not equipped with auxiliary heat. The machine will pause for 30 minutes during any step in which the fill water temperature does not already equal or exceed the programmed value of the heat step. 10. Press the Start key. Supply Options Display Supply SUP0 No Supply SUP1 Supply 1 SUP2 Supply 2 SUP3 Supply 3 SUP4 Supply 4 SUP5 Supply 1 and 2 SUP6 Supply 2 and 3 SUP7 Supply 3 and 4 F232073 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT 23 Safety Cycle Programming (Continued) 11. Use the Up or Down key to select the desired spin time. Set this value to zero to skip the spin step. Press the Start key. The display will now show the identifier for next program segment. Note: An automatic 40-second coast-down follows every high-speed spin. For all spins except the final spin, this coast-down occurs during the fill for the following segment. Therefore, cycle time is not increased for coast-downs following all but the final spin. 12. Press the Stop key at any time to complete the cycle programming procedure. Chemical Injection Supply System The external supply connection ports are designated 1, 2, ...
Questo manuale è adatto anche per i modelli :Lavatrici - Cabinet Hardmount SC35SN (828.96 kb)
Lavatrici - Cabinet Hardmount SC50SN (828.96 kb)
Lavatrici - Cabinet Hardmount SC80SN (828.96 kb)