valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor. Adjusting the leveling feet If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under the feet): 1. Loosen the leg bolt by turning it with your hand until it is at the desired height. 2. Tighten the locking nut by turning it with the supplied wrench. • Place the washer on a sturdy, flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Only a l degrees angle is allowed.) Removing the shipping bolts Before using the washing machine, you must remove the five shipping bolts from the back of the unit. To remove the bolts: 1 2 3 1. Loosen all bolts with the supplied wrench before removing them. 2. Take each bolt head and pull it through the wide part of the hole. Repeat for each bolt. 3. Fill the holes with the supplied plastic covers. 4. Keep the shipping bolts for future use. Connecting the water supply hose(Option) 1. Remove the adaptor from the water supply hose. c 4. Connect the water supply hose to the adaptor. Pull down part (c) of the water supply hose. When you release part (c) the hose automatically connects to the adaptor making a ’click’ sound. 2. First, using a “+” type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow until there is a 5mm gap. 5. Connect the other end of the water supply hose to the inlet water valve at the top of the washer. Screw the hose clockwise all the way in. a b 3. Connect adaptor to the water tap by tightening the screws firmly. Then, turn part (b) following the arrow and put(a) and (b) together. • If the water tap has a screw type faucet, connect the water supply hose to the tap as shown. NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. Use the most conventional type of faucet for water supply. In case the faucet is square or toobig, remove the spacing ring before inserting the faucet into the adaptor. SAMSUNG Washing Machine Owner’s Instructions 3 Installing the Washing Machine Connecting the water supply hose The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose. To connect the water supply hose: 1. Take the L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine. Tighten by hand. 2. Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting. Option: 1. Take the red L-shaped arm fitting for the hot water supply hose and connect to the red hot water supply intake on the back of the machine. Tighten by hand. 2. Connect the other end of the hot water supply hose to your sink's hot water faucet and tighten it by hand. 3. Use a Y-piece if you only want to use cold water. Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used. Positioning the drain hose The end of the drain hose may be positioned in three ways: Over the edge of a sink The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving. ln a sink drain pipe branch The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground. ln a drain pipe Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm. 4 SAMSUNG Washing Machine Owner’s Instructions Installing the Washing Machine Plugging in the machine For European Users. You will NOT need to ground the plug of the washing machine. For U.S. Users. You MUST ground the plug of the washing machine. Check with a licensed electrician before using the machine to make sure it is properly grounded. For U.K. Users. Wiring lnstructions WARNING THIS APPLIANCE MUST BE EARTHED. This appliance must be earthed. In the event of an electrical short circuit, earthing reduces the risk of electric shock providing an escape wire for the electric current. The appliance is equipped with a mains lead which includes an earth wire for connecting to the earth terminal of your mains plug. The plug must be plugged into a socket that is properly installed and earthed. *The wires in this mains lead are coloured in accordance with the following code: • Green and yellow : Earth • Blue : Neutral • Brown : Live • AS the colours of the wires in the mains lea...
Questo manuale è adatto anche per i modelli :Lavatrici - B1245 (340.08 kb)
Lavatrici - B1445 (340.08 kb)
Lavatrici - B1445SGS/XEF (340.08 kb)
Lavatrici - B1445V (340.08 kb)