valutazioni - , GPA:
(
)
)
Produttore : LG
File Size : 3.44 mb
File Nome :
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
Be careful, heavy load! Packing and all transit bolts must be removed before using the washing machine. When unpacking the base, be sure to remove the additional packing support in the middle of the base packing. CD Store original packing for future move. Dispose of packing material according to local regulations. Electrical connection 1. Do not use an extension cord or double adapter. 2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified person to prevent danger. 3. Always unplug the machine and turn off the water supply after use. 4. Connect the machine to an earthed socket in accordance with current wiring regulations. 5. The appliance must be positioned so that the plug is easily accessible. • Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre. • Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point. • If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine standing at room temperature for a few hours before putting it into operation. Transit bolts Connecting water supply hose To prevent internal damage during transport, the special 4 bolts are locked. If they are not removed, It may cause heavy vibration, noise and machine to malfunction. Unscrew the 4 bolts using the spanner supplied. Remove the 4 bolts along with the rubber bungs by slightly twisting the bung. Close the holes with the caps supplied. The hose supplied with the machine must be used. Old hoses may not be reused Water supply pressure must be between 1.0-10 bar (100kPa~1 OOOkPa) Don’t strip or crossthread when connecting inlet hose to the valve, If the water supply pressure is more than 10OOkPa, a decompression device should be installed. • Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks. • Make sure the connection to taps is tight enough. • Periodically check the condition of the hose and replace the hose if necessary. • Make sure that there is no kink on the hose and that it is not crushed. (D Keep the 4 bolts and the spanner for the tuture use. Refit transit bolts before transporting the appliance. 3 Requirements for installation site Level floor: Permissible floor gradient under entire washing machine is 1”. Power socket: Must be within 100 cm of either side of location of washing machine. Do not overload the socket with more than one appliance. Additional Clearance: For wall, floor and door space is needed. (10cm: rear / 2cm:right & left side). Do not place or store laundry products on top of the washing machine at any times. They can damage the finish or controls of the machine. (T) If after completing connection water leaks from the hose, repeat the same steps. Use the most conventional type of tap for water supply. In case the faucet Is square or too big, remove the spacing ring before inserting the tap into the adaptor. Installation of drain hose Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there Is a risk of cockroach infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee. Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is not impeded by carpets, rug etc. • Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine. • If It is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel (85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances. • The washing machine must not be installed In rooms where the temperature may drop below 0°C. • Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown. • Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between the top of the washing machine and underside of the worktop. We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance concerned, without any additional ou...