valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Leave the washing machine door open so that the inside of the washing machine can dry. . Turn off the tap. If the spin function was deactivated at the start of the wash cycle, (no final spin = laundry remains in last rinsing water), the washing programme is automatically stopped after the final rinse. The display panel shows †.‹. alternating with AA:AA. In order to empty the rinsing water and, if required, spin the laundry: Press the 0 (Spin) button repeatedly until the desired spin speed is set. The water is emptying; the washing machine is in spin cycle. The programme has ended when ‹‹‹‹ appears in the display panel. The maximum spin speed depends on the selected washing programme. If you do not wish to spin the laundry: . Set the programme selector to p (Empty). The water is emptying and the washing machine is not in spin cycle. The programme has ended when “Ys appears in the display panel. . Turn the programme selector to $ (Off). . Remove the laundry. . Leave the washing machine door open so that the inside of the washing machine can dry. You have selected the wrong programme by mistake: . Reselect the programme. .‘—† appears in the display panel. . Press inicio/ pausa. The new programme starts from the beginning. Programme termination Press and hold the inicio/ pausa button until .‘—† appears in the display panel. For washing programmes at high temperatures: – Allow laundry to cool: Select q + centrifug. 0 (Rinse + Spin). – Select inicio/ pausa. For programmes at low temperatures: – Select q + centrifug. 0 (Rinse + Spin) or p (Empty). – Select inicio/ pausa. Reset function: – Using the reset function you can return to the original settings. To do this, press and hold the inicio/ pausa button until ‹‹‹‹ appears in the display panel and the three programme progress indicator lamps light up. Cleaning and care Safety information Housing and control panel Washing drum Detergent drawer Descaling the washing machine Risk of electric shock You must first disconnect the appliance from the mains. Never clean the washing machine with a water jet. Risk of explosion. Never clean the washing machine with solvents. Risk of scalding Hot detergent solution must be cooled before being drained. – Remove detergent residue immediately. – Wipe with a soft, damp cloth. – Do not clean with a water jet. – Remove any foreign objects from the drum and rubber seals. – Leave the washing machine door open so that the drum can dry out. – Use chlorine-free cleaning agents; observe the manufacturer's instructions. Never use steel wool. If there are detergent or care product residues: . Pull out the detergent drawer as far as possible. . Press on the zone labelled PUSH and take out the detergent drawer. . Clean the detergent drawer guide. . Remove the fabric softener compartment insert. . Clean the detergent drawer and fabric softener compartment insert under running water. . Insert the fabric softener compartment insert. . Insert the detergent drawer. This should not be necessary if the correct detergent dosage has been used. If it is necessary, however, proceed according to the descaling agent manufacturer's instructions. Suitable descalers can be obtained via our website or from our after-sales service . page 22. Detergent solution pump Information about blockages . Turn the programme selector to $ (Off). . Use a screwdriver to release the lock pins. . Fold down the service panel and remove to the top. Draining the water Cleaning the detergent solution pump . Take the drain hose out of the retainer. . Remove the sealing cap from the drain hose and allow the detergent solution to flow out. – The container for the drained water may have to be emptied several times. – When no more water runs out, put the sealing cap back in place. . Place the drain hose into the retainer. . Carefully unscrew the pump cover (residual water). – Clean the interior, pump cover thread and pump housing (the impeller in the detergent solution pump must be able to rotate). . Refit the pump cover and screw it on tightly. . Place the service cap in the 4 clip-in slots and secure to the housing using the lock pins. To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into compartment II and start the Empty programme. Filter in the water supply *water supply hose depends on model Cleaning the filter on the tap .Connect the hose. Cleaning the filter on the washing machine Cleaning the filter on the washing machine If no (or not enough) water runs into the washing machine, you must first reduce the water pressure in the supply hose: . Turn off the tap. . Choose any programme (except q + centrifug. 0 (Rinse + Spin)/p (Empty)). . Press the inicio/ pausa button. . Allow the programme to run for approximately 40 seconds. . Turn the programme selector to $ (Off).. . Unplug the mains plug from the socket. . Unscrew the water supply hose from the tap. . Clean the filter with a small brush. . Reconnect the hose. . Tur...
Questo manuale è adatto anche per i modelli :Lavatrici - WI12A220EE/02 (1.06 mb)