valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
a Caution! The appliance may become damaged. If the end of the drain hose is immersed in the drained water, water may be sucked back into the appliance. – The plug must not block drainage from the sink. – Small hand wash basins are not suitable. – During emptying, check whether the water is draining away quickly enough. – The end of the outlet hose must not be immersed in the drained water. 31 32 Routing the drain hose: . The elbow must be secured right at the end of the drain hose. Drainage into a siphon a Warning! Water damage possible! If the drainage hose slips off the siphon connection due to high water pressure when draining the washing machine, leaking water may cause damage. Connection point must be secured with hose clip, O 24–40 mm (specialist outlet). Connecting Outlet to a plastic pipe with rubber bushing a Warning! Possible water damage! If the drain hose slips out of the plastic pipe during draining due to the high water pressure, any escaping water may cause water damage. Secure the drain hose so that it cannot slip out. Connection Alignment 1. Undo the lock nut with a wrench in the direction of the arrow. 2. Check the alignment of the washing machine with a spirit level and adjust if necessary. Change the height by turning the appliance feet. . All appliance feet must stand firmly on the ground. The washing machine must not wobble. 3. Tighten the lock nut against the housing. In doing so, hold the foot tight and do not adjust its height. . – The lock nuts on all of the appliance feet must be screwed tightly against the housing. – Intense noise, vibrations and "wandering" may be the result of incorrect levelling. 33 Electrical connection Electrical safety a Warning! Danger of death from electric shock! Danger of death if live parts are touched. – Never pull out the mains plug by tugging the power cord. – Insert/pull out the mains plug with dry hands only. – Never pull out the mains plug during operation. – Connect the washing machine to an alternating current via a correctly installed earthed socket only. – The mains voltage and voltage specifications on the washing machine (appliance rating plate) must match. – Connected load as well as required fuse are indicated on the appliance rating plate. Ensure that: – Mains plug and socket match fit. – Cable cross-section is adequate. – Earthing system has been installed correctly. – A damaged power cord may be replaced by an electrician only. A replacement mains cable can be obtained from customer service. – Do not use multiple plugs/couplings or extension cables. – If a residual-current-operated circuit breaker is used, use only a type which features this symbol: z. Only this symbol guarantees compliance with currently valid regulations. – The mains plug must be accessible at all times. 34 Before the 1st washing The washing machine was thoroughly tested before leaving the factory. To remove any water that may be left over from the test, do not load any laundry the first time that you run a washing programme. The washing machine must be installed and connected correctly . as described in the Installation chapter from ~Page 33 onwards. 1. Check the machine. . Never use a damaged machine. Inform the after-sales service. ~Page 24 2. Remove the protective film from the display (if present). 3. Connect the mains plug. 4. Turn the tap on. 5. Open the lid; make sure that the drum flaps are closed correctly (do not load any laundry). 6. Select the cottons programme. 7. Set the temperature to 60 °C. 8. Add 1/3 of the amount of standard detergent recommended by the manufacturer for light soiling to compartment II. . To prevent foaming, only use approximately a third of the recommended amount of detergent. Do not use detergent for wool or delicates. 9. Close the lid. 10. Select start/pause. 11. At the end of the programme, turn the programme selector to "Off”. Your washing machine is now ready to use. 35 Transportation, e.g. if moving house Preparatory work 1. Disconnect the mains plug. 2. Turn off the tap. 3. Remove the water supply and drain hose. 4. Wait until the water has cooled in order to prevent scalding. Drain the remaining detergent solution. Maintenance – detergent solution pump blocked ~Page 19 5. For easier transport, slightly pull out the handle at the bottom of the appliance on the front (depending on the model). If necessary, use foot to help pull out the handle fully. Fitting the transport lock 1. Refit the transport lock. 2. Transport the appliance in an upright position. Before initial use: . – You must remove the transport lock. ~Page 29 – Return the transport handle to its original position. – To prevent unused detergent from flowing straight into the drain during the next wash: Pour 1 litre of water into the drum and start the drain or clear/drain programme (depending on the model). 36 Index A Alignment, 33 C Cancelling the Childproof lock, 15 programme, 15 Cleaning Care, 17 Detergent dispenser, 17 Drum, 17 Filter, 19 Machine housing/cont...
Questo manuale è adatto anche per i modelli :Lavatrici - WOT24254EE/02 (1.76 mb)