Installation and maintenance instructions, Page 3. ..Please clean lint filter is displayed. Clean the fluff filters ..Page 4. Press the Inicio/Pausa + Carga (Start/Pause) ..button again. ..Dryer does not start. Has the Inicio/Pausa + Carga (Start/Pause) ..button been pressed? Door closed? Ambient temperature greater than 5 °C? ..Water is leaking out. Make sure the dryer is level. Push the condensation container back in until it locks fully into place. 10Normal noises During drying, the compressor and the pump generate some noise which is entirely normal. The compressor in the dryer may occasionally generate a humming noise. The volume and pitch of this may vary depending on the selected programmes and the progress of the drying. The compressor in the dryer is ventilated from time to time, which creates a whirring sound. The automatic cleaning process causes a clicking noise. The process of pumping the condensation into the condensation container generates pumping noises. 11What to do if ... If you cannot rectify a fault yourself (e.g. by switching the dryer off/on), please contact our after-sales service. We will always find an appropriate solution and will avoid unnecessary visits by engineers. Trust the expertise of the manufacturer and rest assured that the repair will be carried out by trained service technicians using original spare parts. The contact details of your local after-sales service can be found in the enclosed after-sales service directory: – GB 0844 8928999 (Calls from a BT landline will be charged at up to 3 pence per minute. A call set-up fee of up to 6 pence may apply.) – IE 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.) When contacting the after-sales service, please specify the product number (E-Nr.) and production number (FD) of your appliance(see inside of door). Switch the dryer off using the programme selector and unplug the mains plug from the socket. ..Please empty condensate container is displayed. Emptying the condensation container ....Page 4. Press any button. Press the Inicio/Pausa + Carga (Start/Pause) ..button again. ..Please empty condensate container is displayed and the drying cycle is interrupted. Is the condensation drain installed? ....Condensation drain hose blocked ..check and clean the hose. Stopper in the condensation container? ....separate Instructions for condensation drain. Is the filter in the condensation container dirty? .... Clean the filter in the condensation container .. Installation and maintenance instructions, Page 3. ..Please clean lint filter is displayed. Clean the fluff filters ..Page 4. Press the Inicio/Pausa + Carga (Start/Pause) ..button again. ..Dryer does not start. Has the Inicio/Pausa + Carga (Start/Pause) ..button been pressed? Door closed? Ambient temperature greater than 5 °C? ..Water is leaking out. Make sure the dryer is level. Push the condensation container back in until it locks fully into place. 12 What to do if ... ..Drying result was not achieved (laundry too damp). Warm laundry feels damper than it really is. The selected programme does not suit the load. Use another drying programme or, in addition, select the time programme ..Programme overview, Page7. Use the « ....Adjust drying level »option ..Page 5. Thin layer of limescale on the moisture sensors? Clean the moisture sensors ....Installation and maintenance instructions, Page 2. Programme termination, e.g. condensation container full, mains power supply failure, door open or maximum drying time reached. ..Drying time too long. Clean the fluff filters under running water ..Page 4. Insufficient supply of air ..Ensure that air can circulate. Air inlet may be obstructed? Clear the inlet ....Installation and maintenance instructions, Page 1. Ambient temperature higher than 35 °C ..Ventilate the room. ..The humidity in the room increases significantly. Make sure the room is sufficiently ventilated. ..Heat exchanger is being rinsed is displayed in the display panel. Not an error. Automatic cleaning of the heat exchanger. Do not empty the condensation container during the cleaning process. ..Power failure. As a result of a power failure, the programme is cancelled. If the laundry is still too damp: Switch on the appliance and restart the programme. ..Other intermittent noises and vibrations. Normal noises ..Page 10. 12 What to do if ... ..Drying result was not achieved (laundry too damp). Warm laundry feels damper than it really is. The selected programme does not suit the load. Use another drying programme or, in addition, select the time programme ..Programme overview, Page7. Use the « ....Adjust drying level »option ..Page 5. Thin layer of limescale on the moisture sensors? Clean the moisture sensors ....Installation and maintenance instructions, Page 2. Programme termination, e.g. condensation container full, mains power supply failure, door open or maximum drying time reached. ..Drying time too long. Clean the fluff filters under running water ..Page 4...

Questo manuale è adatto anche per i modelli :
Lavatrici - WT47Y780NL/07 (2.92 mb)