valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
• When unpacking the appliance, check that it is not damaged. If in doubt, do not use it and contact the retailer. • All internal packing must be removed before using the appliance. Serious damage may be caused to the machine or adjacent furniture if the protective transit devices are not removed or are not completely removed. Refer to the relevant paragraph. • Any electrical work required to install this appliance must be carried out by a qualified electrician or competent person. • Any plumbing work required to install this appliance must be carried out by a qualified plumber or competent person. • After having installed the machine, check that it is not standing on its electrical supply cable. • If the appliance is placed on a carpeted floor, ensure that air can circulate freely between the adjustable feet and the floor. • The installation should comply with local water authority and building regulations requirements. • Should the appliance power supply cable need to be replaced, this should be carried out by our Service Force Centre. Dimensions of the appliance Front view and side view Rear view 49 ! ! " " # $ $ # $ " ! Installation Unpacking All transit bolts and packing must be removed before using the appliance. Using a spanner, unscrew and remove the rear right-hand bolt and lay the machine on its back, taking care not to squash the hoses. This can be avoided by placing one of the corner packing pieces between the machine and the floor. Remove the polystyrene base and take off the bottom panel by unscrewing the central screw. Carefully slide out the right polythene bag. Repeat the operation for the left and central polythene bags. Re-fit the bottom panel using the 4 screws supplied with the door hinges (in the plastic bag) and the previously removed screw. y Installation Set the machine upright and remove the two remaining bolts from the back. Pull out the three plastic spacers from the holes into which the bolts were fitted. Plug the open holes with the plugs which you will find in the plastic bag containing the instruction booklet. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. Positioning Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. • Before placing it on small tiles, apply a rubber coating. • Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine. • If it is impossible to avoid positioning the machine next to a gas cooker or coal-burning stove, an insulating panel (85x57 cm) covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances; • The machine must not be installed in rooms where the temperature can drop below 0°C. • The water inlet hose and the drain hose must not be kinked. • Please ensure that when the appliance is installed, it is easily accessible for the engineer in the event of a breakdown. Levelling Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. . Installation Water inlet (cold water connection only) Connect the hose to a tap with a 3/4” thread. Installation should comply with local water authority and building regulations’ requirements. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. Do not connect to a hot water supply. The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window “A”. Should this occur, turn the water tap off and refer to your Service Force Centre to replace . the hose. Water drainage The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied. The standpipe should have an internal diameter of approximately 38 mm (see diagram) thus ensuring there is an air break between the drain hose and standpipe. When discharging into a stand-". pipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4”) and no less than 60 cm (23.6”) above floor level. The upright standpipe should have a minimum length of 30 cm (12”) from the bottom of the elbow to the top of the pipe (see diagram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water. # $% %&"%'(#%%&!"%'( yInstallatio Longer drain hoses are available in lengths of 2.7 and 4 metres from your AEG Service Force Centre. If you intend the drain hose from the machine to empty into a sink, make sure that the sink is empty and the plug hole is not blocked. Use t...