valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
French on back
WASHING
Spanish on back
MACHINE
INSTALLATION GUIDE 5 CONNECTING THE DRAIN HOSE.
Case 1. Wash basin
Case 2. Laundry tub Hose Case 3. Stand pipe
Parts supplied
Tools needed
Drain hose
retainer
Hose
retainer
8” Max
6” Min
96” Max
Type1
Type2
18” Min
96” Max
Tie strap
carpenter’s
18” Min
Wrench
Bolt hole covers
Water supply hoses
Hose guide
(option)
Tape measure
level
Pilers
Flat screwdrilver
Tie strap
1
Hose guide
Tie strap
PREPARATION.
To keep the drain hose
The drain hose must be
Laundry tub must be no
Do not insert the drain hose
1. Check the instal ation location. □ CHECK : Solidly constructed floor (Not Carpeting and soft tile surfaces)
spout bent, use the
placed at a height between shorter than 18 in (46 cm) too far into the stand pipe: 6
2. And move the washer to the instal ation location.
supplied plastic hose
23.6 in (60cm) and 35.4 in and no longer than 96 in
- 8 inches, and no more.
guide.
(90cm).
(245 cm).
* When instal ing the washer on a pedestal, do the instal ation before next step.
2 REMOVING ALL SHIPPING BOLTS.
6 MOVE THE WASHER TO ITS FINAL LOCATION AND MAKE SURE IT IS LEVELED.
Remove all shipping bolts Hold the shipping bolt
Fill the holes with the
at the back of washer with with your hand and pull it
supplied bolt hole covers.
Confirm whether washer is well seated and does not
Your washer must be leveled on all four sides. Use a
supplied spanner.
through the wide section of
the hole. Repeat for each
shake. Adjust leveling legs, if necessary.
carpenter’s level on all four corners of your washer to
shipping bolt.
ensure it’s level.
CAUTION: Failure to remove the shipping bolts wil cause vibration and noise.
7 LEVEL THE WASHER BY ADJUSTING THE FOUR LEVELING LEGS.
3 COLD & HOT WATER HOSES INSTALLATION ON FAUCETS.
HOT COLD
Rubber washer
Level the washer by turning the leveling
Check whether washer shakes
When your washer is leveled,
wheel in or out as required by using the
and level again, if necessary.
tighten the locking nuts using the
Coupling
Rubber
washer
supplied wrench.
wrench or (-) flathead screwdriver.
Make sure a Rubber
Tighten Coupling by hand Then tighten two-thirds of a Run water in a bowl or
CAUTION: Your washer must be leveled on al four sides. An unlevel washer may cause vibration.
washer is inside each
until it is snug.
turn with pliers.
basin to get rid of any debris
coupling on both ends.
inside hose. Check for HOT
and Cold water supply.
8 Final Test : Water leakage , Vibration & Noise
4
1. Powering your washing machine.
WATER HOSES INSTALLATION ON WASHER.
2. Run a test cycle(Rinse+Spin) with small amount of laundry such as 4~5 Towels.
(1) Check for any leakage at the hose connections.
If water leaks while water is being supplied or drained, check the water connections. (Refer to Step 3,4,5)
COLD (Left)
HOT (Right)
Water
Water
(2) Check for vibration and noise.
If the washer rocks and vibrates excessively, level your washer again. (Refer to Step 6,7)
Visits by a Service Engineer to explain functions, maintenance or installation is
not covered by warranty.
Connect one end of the
Tighten Coupling by hand Then tighten two-thirds of a For proper operation, make
COLD/HOT water supply
until it is snug.
turn with pliers.
sure both Hot & Cold hoses
INSTALLATION
hoses to the each COLD/
from faucets are connected to
□ No water leakage
□ No vibration / noise
COMPLETION CHECKLIST
HOT water supply intakes
the corresponding Hot / Cold
□ Water hose connected properly □ Washer leveled
at the back of the washer.
water inlets on the washer.
□ Washer plugged in, power OK
□ Drain hose connected properly □ Shipping bolts removed
CAUTION: Make sure that the HOT & COLD hoses are switched with each other.
DC68-02580C-04
Installation Guide-02580C-03_EnCfrMes.indd 1
2012-07-20 �� 3:28:58
... Questo manuale è adatto anche per i modelli :
Lavatrici - Front Load Washer With Pure Wash (WF363BT) (1.41 mb)
Lavatrici - Front Load Washer With Pure Cycle (WF501A) (1.41 mb)
Lavatrici - Front Load Washer With Pure Wash (WF393BT) (1.41 mb)
Lavatrici - Front Load Washer With Pure Wash (WF395BT) (1.41 mb)