Log:
valutazioni - 1, GPA: 4 ( )

Istruzioni per l'uso Grizzly, Modello T20644

Produttore : Grizzly
File Size : 1.36 mb
File Nome : 02a96f10-80a6-4b64-c9f6-1aa455c33545.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


.... .... .... .... .... .. .... .... .... .... .... .... .... .... .... .... PARTS LIST REF PART # DESCRIPTION REF PART # DESCRIPTION PT20644001 SPECIAL CAP SCREW PT20644002 AIR DEFLECTOR PT20644003 RUBBER WASHER PSB38M CAP SCREW M5-.8 X 25 PLW01M LOCK WASHER 5MM PT20644006 CYLINDER COVER PSS79M SET SCREW M4-.7 x 6 PT20644008 COMPRESSION SPRING PT20644009 SWITCH VALVE SEAT PORG030 O-RING 29.4 X 3.1 G30 PORG045 O-RING 44.4 X 3.1 G45 PT20644012 SWITCH VALVE PT20644013 COLLAR PORG065 O-RING 64.4 X 3.1 G65 PT20644015 FIXED RING PT20644016 SEALING WASHER PT20644017 CYLINDER PORP035 O-RING 34.7 X 3.5 P35 PT20644019 PISTON PT20644020 BUMPER PT20644021 GUIDE PT20644022 GASKET PT20644023 GUN BODY PT20644024 RUBBER WASHER PT20644025 O-RING 15 X 2.65 PORS018 O-RING 17.5 X 1.5 S18 PT20644027 TRIGGER VALVE SEAT PH7665031 O-RING 6.2 X 1.8 PH7665032 O-RING 6.4 X 2 PH7665033 O-RING 9 X 1.8 PT20644031 TRIGGER VALVE GUIDE PH7665036 O-RING 2.5 X 1.5 PT20644033 SWITCH VALVE SPRING PT20644034 SWITCH VALVE STEM PH7665037 O-RING 20.3 X 2.3 PT20644036 TRIGGER VALVE SEAT PT20644037 COMPRESSION SPRING PRP02M ROLL PIN 3 X 16 PT20644039 SAFETY SPACER PT20644040 PIN PT20644041 TRIGGER PT20644042 O-RING 1.7 X 2 PT20644043 SAFETY SEAT PN04M HEX NUT M4-.7 PT20644045 ADJUSTING NUT PT20644046 STEEL BALL 2MM PT20644047 COMPRESSION SPRING PRP97M ROLL PIN 3 X 30 PT20644049 COMPRESSION SPRING PT20644050 DRIVE STAND 51 PT20644051 SPACER 52 PEC09M E-CLIP 6MM 53 PT20644053 COMPRESSION SPRING 54 PT20644054 SAFETY NOSE 55 PT20644055 SAFETY COVER 56 PSB17M CAP SCREW M4-.7 x 10 57 PEC01M E-CLIP 3MM 58 PSB18M CAP SCREW M4-.7 x 8 59 PT20644059 FIXED COVER 60 PLW03M LOCK WASHER 6MM 61 PSB02M CAP SCREW M6-1 x 20 62 PT20644062 RUBBER RETAINING RING 63 PT20644063 QUICK RELEASE HANDLE 64 PT20644064 LATCH 65 PT20644065 DRIVER GUIDE COVER 66 PRP43M ROLL PIN 3 X 22 67 PT20644067 PIN 68 PT20644068 DRIVE GUIDE 69 PT20644069 SPACER 70 PSB23M CAP SCREW M4-.7 x 12 71 PW05M FLAT WASHER 4MM 72 PT20644072 LOCK SCREW 73 PT20644073 MAGAZINE 74 PT20644074 FIXED SEAT 75 PT20644075 PUSHER SPRING 76 PT20644076 PUSHER PIN 77 PT20644077 PUSHER SEAT 78 PT20644078 SPRING CORE 79 PT20644079 TORSION SPRING 80 PT20644080 PUSHER 81 PN04M HEX NUT M4-.7 82 PT20644082 DRIVE NAIL BAR 83 PSB33M CAP SCREW M5-.8 x 12 84 PW02M FLAT WASHER 5MM 85 PT20644085 SUPPORT SEAT 86 PFN04M FLANGE NUT M5-.8 87 PT20644087 RUBBER HANDLE CASE 88 PT20644088 END CAP GASKET 89 PT20644089 END CAP 90 PSB53M CAP SCREW M5-.8 x 18 91 PT20644091 MALE AIR PLUG 1/4" NPT 92 PT20644092 AIR PLUG DUST COVER 93 PAW03M HEX WRENCH 3MM 94 PAW04M HEX WRENCH 4MM 95 PAW05M HEX WRENCH 5MM 96 PT20644096 CARRYING CASE 97 PT20644097 COMPLETE O-RING KIT 98 PT20644098 PISTON REPAIR KIT 99 PT20644099 SAFETY GLASSES T20644 34° Angle Finish Nailer–2." -17 TROUBLESHOOTING Symptom Possible Cause Solution Air leaking at trigger valve area. 1. O-rings in trigger valve housing are damaged. 1. O-rings must be replaced & operation of safety nose must be checked. Air leaking. 1. Loose screws in housing. 1. Tighten screws. 2. Damaged O-ring(s). 2. Replace O-ring(s). 3. Loose air fitting. 3. Tighten air fitting & use teflon tape. 4. Damaged housing gasket(s). 4. Replace gasket(s). Tool skips nails 1. Excessive air pressure. 1. Reduce air pressure to tool. while discharging. 2. Air leaks. 3. Dirt in nose. 4. Dirt or damage prevents nails from moving freely in magazine. 5. Inadequate air flow to tool. 6. Worn O-ring on piston or lack of lubrication. 7. Damaged O-rings on trigger valve. 8. Worn bumper. 9. Cap seal leaking. 2. Tighten screws and fittings. 3. Clean nose. 4. Clean magazine and inspect/repair damage. 5. Check fitting, hose, compressor & air pressure. 6. Replace piston O-ring. Lubricate. 7. Replace trigger valve O- rings. 8. Replace bumper. 9. Replace cap seal. Tool runs slowly 1. Undersized air hose. 1. Use a larger air hose. or has a loss of 2. Nailer is not lubricated. 2. Lubricate nailer. power. 3. Broken spring in cap assembly. 4. Exhaust port in cap is blocked. 5. Air pressure too low. 3. Replace spring. 4. Clean or replace damaged internal parts. 5. Increase air pressure. Fasteners frequent1. Nails are the wrong size. 1. Use correct nails. ly jam the nailer. 2. Nails are bent or dirty. 3. Magazine or nose screws are loose. 4. Driver or driver guide are worn or damaged. 5. Nails are wrong angle. 2. Use undamaged, clean nails. 3. Tighten magazine. 4. Replace worn or damaged parts. 5. Use correct angle nails. Nailer does not fire. 1. Nailer is not lubricated. 2. Nail is jammed in magazine or discharge area. 3. Piston shaft is damaged. 4. Air pressure too low. 1. Lubricate nailer. 2. Clear nailer magazine or discharge area. 3. Replace piston shaft. 4. Check/increase air pressure. -18-T20644 34° Angle Finish Nailer–2." WARRANTY AND RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirect...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie