valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
. .Never use this tool in a manner that could cause a fastener to be directed toward anything other than the workpiece. . .Do not use the tool as a hammer. . .Always carry the tool by the handle. Never carry the tool by the air hose. . .Do not alter or modify this tool from the original design or function without approval from the manufacturer. . .Always be aware that misuse and improper handling of this tool can cause injury to yourself and others. . .Never clamp or tape the trigger or workpiece contact in an actuated position. . .Never leave a tool unattended with the air hose attached. . .Do not operate this tool if it does not contain a legible warning label. . .Do not continue to use a tool that leaks air or does not function properly. operation . Always assume that the tool contains fasteners. . Do not carry the tool from place to place holding the trigger. Accidental discharge could result. . Always handle the tool with care: • Respect the tool as a working implement. • Never engage in horseplay. • Never pull the trigger unless nose is directed toward the work. • Keep others a safe distance from the tool while tool is in operation as accidental actuation may occur, possibly causing injury. . Choice of triggering method is important. Check manual for triggering options. . Pneumatic tools are designed for single-hand use. Do not hold the tool by the front of the magazine. Do not put hands, head, or other parts of your body near the bottom of the magazine where the nail exits the tool, as serious personal injury could result. . Do not point the tool toward yourself or anyone whether it contains fasteners or not. . Do not actuate the tool unless you intend to drive a fastener into the workpiece. . Always ensure that the workpiece contact is fully positioned on the workpiece. Positioning the work contact element only partially on the workpiece could cause the fastener to miss the workpiece completely and result in serious personal injury. . Do not drive fasteners near edge of material. The workpiece may split causing the fastener to ricochet, injuring you or a co-worker. Be aware that the nail or fastener may follow the grain of the wood, causing it to protrude unexpectedly from the side of the work material. . Keep hands and body parts clear of immediate work area. Hold workpiece with clamps when necessary to keep hands and body out of potential harm. Be sure the workpiece is properly secured before pressing the nailer against the material. The workpiece contact may cause the work material to shift unexpectedly. . Keep face and body parts away from back of the tool cap when working in restricted areas. Sudden recoil can result in impact to the body, especially when nailing into hard or dense material. . During normal use the tool will recoil immediately after driving a fastener. This is a normal function of the tool. Do not attempt to prevent the recoil by holding the nailer against the work. Restriction to the recoil can result in a second fastener being driven from the nailer. Grip the handle firmly and let the tool do the work. Failure to heed this warning can result in serious personal injury. . Do not drive fasteners on top of other fasteners or with the tool at an overly steep angle as this may cause deflection of fasteners which could cause injury. . Do not drive fasteners close to the edge of the workpiece as the wood may split, allowing the fastener to be deflected possibly causing injury. AIR SUPPLY AND CONNECTIONS . .Do not use oxygen, combustible gases or bottled gases as a power source for this tool as tool will explode, possibly causing injury or death. . Do not use with an air compressor which can potentially exceed 200 psi as tool may burst, possibly causing injury. . The connector on the tool must not hold pressure when air supply is disconnected. If an incorrect fitting is used, the tool can remain charged with air after disconnecting and thus will be able to drive a fastener even after the air line is disconnected, possibly causing injury. . Always disconnect air supply: • Before making adjustments • When servicing the tool • When clearing a jam • When tool is not in use • When moving to a different work area, as accidental actuation may occur, possibly causing injury. loading tool . Do not load the tool with fasteners when any one of the operating controls is activated. When loading tool: . Never place a hand or any part of body in fastener discharge area of tool. . Never point tool at anyone. . Do not pull the trigger or depress the workpiece contact as accidental actuation may occur, possibly causing injury. Save these instructions . Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also. specific SAFETY RULES SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING Indicates an imminently hazardous situation,...