valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Wipe off any excess oil from the cap exhaust. Recommended Hookup The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch or greater air hoses for 50 foot run or longer. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 70 and 110 psi. O CO2 100 psi 150 psi or greater 60 psi Min. 100 psi Max. Recommended Hookup Quick Plug Air Hose Quick Plug (Optional) Regulator Filter Quick Coupler Lubricator Quick Coupler (Optional) OIL 5 Operating Instructions NB003006 Operating Instructions (Continued) Sequential Trip Safety Mechanism This tool is equipped with a sequential trip safety mechanism. When the operator depresses the Work Contact Element (WCE) against the work surface and then pulls the trigger, a fastener will be driven. Operating a se quential trip nailer 1. Release trigger and place nose of tool against work surface. 2. Depress the Work Contact Element (WCE) against the work surface and pull the trigger to drive a fastener. 3. Release the trigger and lift the tool from the work surface after each fastener is driven. Checking the Work contact element (WCE) Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (see Loading/ Unloading). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the nailer. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The nailer must not operate . Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the nailer from the work surface. The Work Contact Element (WCE) must return to its original down position. The nailer must not operate . Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the work contact element (WCE) against the work surface. The nailer MUST NOT operate . 8. Depress the Work Contact Element (WCE) against the work surface. Pull the trigger. The nailer MUST operate . An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed firmly against the work piece. Loading /Unloading The Nailer 1. Always disconnect the tool from the air supply before loading fasteners. 2. Lift up on the latch. Pull back on the magazine cover. 3. Insert a stick of Campbell Hausfeld nails or equivalent (See Fastener Section) into the magazine. Make sure the pointed ends of the nails are resting on the bottom ledge of the magazine when loading. Make sure the nails are not dirty or damaged. 4. Push the magazine cover forward until the latch catches. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. Adjusting the Nail Penetration 1. Regulate the air pressure to 60 psi at the nailer. 2. Connect the air supply and test for penetration by driving nails into a sample piece of wood. If the nails do not achieve the desired penetration, adjust the air pressure to a higher setting until the desired penetration is achieved. Do not exceed 100 psi at the nailer or durability of the nailer will be reduced. User - Maintenance Instructions Clearing A Jam From The Tool 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (See Loading/ Unloading The Nailer). Failure to do so will cause the nails to eject from the front of the nailer when the nose assembly is removed. 3. Pull red tab forward on quick clear nose. Set aside nose door to expose and remove jammed fastener. 4. Reinstall nose in reverse order in step 3. 5. Make sure the trigger and Work Contact Element (WCE) move freely up and down without sticking or binding. 100 0 200 50 150 100 0 200 50 150 Operating Instructions NB003006 User -Maintenance TOOL REPAIR STORAGE Instructions (Continued) Only qualified pe...
Questo manuale è adatto anche per i modelli :Chiodatrici - CHN90498 (9.68 mb)