valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Do not actuate the tool unless the tool is placed firmly against the work piece. Loading / Unloading The Tool 1. Always disconnect the tool from the air supply before loading fasteners. 2. Push down on the latch button. Pull back on the magazine cover. 3. Load a clip of fasteners with the crowns straddling the magazine rail. 4. Push the magazine cover forward until latch button pops up. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except always disconnect the air hose before unloading. Adjusting the Nail Penetration The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust operating pressure so nails are driven consistently. Do not exceed 100 psi. 2. To drive the nail shallower, turn the wheel (C) to right to the extent desired. 3. To sink a nail deeper, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element move freely up and down without binding or sticking after each adjustment. Adjusting The Direction Of The Exhaust The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. 1 2 1 2 Rotate 1 2 (C) 6 Operating Instructions CHN10302, CHN10310 User - Maintenance Instructions Clearing A Jam From The Tool 1. Disconnect the air supply from the tool. 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to remove all fasteners will cause the fasteners to eject from the front of the tool. 3. Undo latch by pulling out and down. The wire latch will disengage from the hooks on the nose. 4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a screwdriver if required. 6. Rotate door back into the closed position. 7. Extend the wire latch and place over the hooks on the nose. 8. Close the latch by pushing the latch up and in until the latch snaps into place. 9. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. Technical Ser vice Please call our Tool Hotline at 1-800- 543-6400 with any questions regarding the operation or repair of this tool or for additional copies of this manual. Fastener And Replacement Parts Use only headless micropins, 18 gauge. Tool performance, safety and durability could be reduced if improper fasteners are used. When ordering replacement parts or fasteners, specify by part number. Tool Repair Only qualified personnel should repair the tool and they should use genuine Campbell Hausfeld replacement parts and accessories, or parts and accessories which perform equivalently. Assem bly Procedure For Seals When repairing a tool, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non-detergent oil or equivalent, must be added through the air line before testing. Storage The tool should be stored in a cool dry place. Fasteners The following Campbell Hausfeld finishing nails are available at local retail stores. If you need help locating any item, call customer service at 1-800-543-6400. Campbell Hausfeld nails meet or exceed ASTM Standard F1667. Model Length Wire Diameter Crown Size Point Finish Collation Nails Per Stick Nails Per Box FN180615AV 1/2 inch 18 Gauge 1/4 inch Chisel Galvanized / Vinyl Coated Adhesive 100 1000 FN180620AV 3/4 inch 18 Gauge 1/4 inch Chisel Galvanized / Vinyl Coated Adhesive 100 1000 FN180625AV 1 inch 18 Gauge 1/4 inch Chisel Galvanized / Vinyl Coated Adhesive 100 1000 FN180630AV 1-1/4 inch 18 Gauge 1/4 inch Chisel Galvanized / Vinyl Coated Adhesive 100 1000 Interchange Information Staples used in the Finishing Stapler will also work in: Senco LN4450, SJS-LR, SKS L11-15, Hitachi N3804A, Duofast BN-1832S, KN-1848, Stan-Tech SDS 18-14, Atro Minor 90/30, 90/32, 90/40, and Porter Cable NS100. Operating Instructions CHN10302, CHN10310 Troubleshooting Chart Stop using tool immediately if any of the following problems occur. Serious personal injury could occur. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Symptom Possible Cause(s) Corrective Action Air leaking at trigger valve O-rings in trigger valve housing are Replace o-rings and check operation of Work area. damaged Contact Element (WCE) Air leaking between housing and nose. 1. Loose screws in housing 2. Damaged o-rings 3. Damage to bumper 1. Tighten screws 2. Replace o-rings 3. Replace bumper Air leaking between housing and cap. 1. Loose screws 2. Damaged gasket 1. Tighten screws 2. Replace gasket Tool skips driving fastener 1. Worn bumper 1. Replace bumper 2. Dirt in nose...
Questo manuale è adatto anche per i modelli :Chiodatrici - CHN10310 (11.26 mb)