valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Place one drop of oil in the nailer/stapler air inlet (as shown in Figure 5) before every use. Wipe off any excess oil near the nailer/stapler exhaust to avoid dust build-up. When the oil that was included with the nailer/stapler has been completely used, replace with Grizzly Model G2820 Pneumatic Tool Oil. Another option to manual oiling would be to install a lubricator in your air compressor line. If your air compressor line already has a lubricator, then regular lubrication of your nailer/stapler will not be necessary. Just make sure there is always oil in the lubricator. As mentioned before, the best option is to install a filter/lubricator/regulator unit such as the Grizzly Model H2333 in your air line. Figure 5. Lubricating the nailer/stapler via air inlet. Cleaning The Nailer/Stapler Use a good solvent to clean the nose assembly of the nailer/stapler. Always be sure that the nailer/stapler is dry before using it again. Do not allow dust, chips, sand, etc. into the air connectors or into the body of the nailer/ stapler; this may result in leaks and damage to the nailer/stapler and the air couplings. Never use gasoline or other flammable liquids to clean this tool. Vapors in the tool may ignite, causing the tool to explode. Ignoring this warning may lead to serious personal injury or even death! Always disconnect air from the nailer/ stapler whenever servicing! During maintenance, a nailer/stapler connected to air may fire accidentally, causing serious personal injury! H2912/H2913 2-IN-1 NAILER/STAPLER -8 Replacing Pistons/O-Rings If you use your nailer/stapler day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or piston shaft becomes worn out. To replace a piston: Always disconnect air from the nailer/ stapler whenever servicing! During maintenance, a nailer/stapler connected to air may fire accidentally, causing serious personal injury! 1. Disconnect the nailer/stapler from the air supply! 2. Remove all staples/nails from the magazine cartridge. 3. Remove the 4 cap screws from the exhaust cap. 4. Remove the exhaust cap as shown in Figure 6. 5. The top of the piston should now be visible inside the cylinder, which is housed in the head. 6. Open the magazine. 7. Watch the discharge area and push the top of the piston with your finger. You will see the piston shaft slide down the discharge area. Figure 6. Removing the exhaust cap. 8. With a long flathead screwdriver or similarly shaped tool, push the piston shaft back inside the nailer/stapler until you can grip the piston head and remove it from the cylinder. (Be careful not to scratch the discharge area when pushing the piston shaft with the screwdriver.) 9. Place a new O-ring on the new piston and apply a thin film of lubricating oil on the O-ring. 10. Insert the new piston in the cylinder. Make sure that the grooves on the piston shaft line up with those on the guide. The new piston should easily slide into the cylinder. Do not force the piston into the cylinder! If the piston is not easily inserted, double- check the alignment of the piston shaft with the grooves on the guide. 11. After the piston is inserted correctly, close the magazine. Replace the rear cap assembly and tighten the 4 cap screws. 12. For more assistance, or to install a complete O-ring set, refer to the appropriate breakdown diagram in the back of this manual. -9- H2912/H2913 2-IN-1 NAILER/STAPLER H2912 PART BREAKDOWN H2912/H2913 2-IN-1 NAILER/STAPLER -10 REF PART # DESCRIPTION REF PART # DESCRIPTION 01 PH2912001 CAP SCREW 02 PH2912002 CAP COVER 03 PH2912003 SEAL 04 PH2912004 CAP SCREW PH2912005 SETSCREW 06 PH2912006 CAP 07 PH2912007 PISTON STOPPER 08 PH2912008 O-RING 09 PH2912009 COLLAR PH2912010 O-RING 11 PH2912011 SPRING 12 PH2912012 PISTON HEAD VALVE 13 PH2912013 O-RING 14 PH2912014 O-RING PH2912015 O-RING 16A PH2912016A PISTON ASSEMBLY 17 PH2912017 CYLINDER 18 PH2912018 O-RING 19 PH2912019 BUMPER PH2912020 GASKET 21 PH2912021 O-RING 22 PH2912022 BODY 23 PH2912023 CAP SCREW 24 PH2912024 AIR PLUG PH2912025 JOINT GUIDE 26 PH2912026 STEPPED PIN 27 PH2912027 SPRING 28 PH2912028 SAFETY LEVER 29 PH2912029 LOCK NUT PH2912030 POSITIONING PLATE 31 PH2912031 ADJUSTMENT NUT 32 PH2912032 GUIDE PLATE 35A PH2912035A BUMP FIREB SWITCH 36 PH2912036 SET SHAFT 37 PH2912037 SAFETY LEVER 38 PH2912038 LOCK WASHER 39 PH2912039 CAP SCREW 40 PH2912040 RUBBER PAD 41 PH2912041 CAP SCREW 42 PH2912042 SOCKET 43 PH2912043 NOSE COVER 44 PH2912044 NOSE COVER 45 PH2912045 CAP SCREW 47 PH2912047 NOSE 48 PH2912048 SET PLATE 49 PH2912049 SET PLATE 50 PH2912050 BRACKET 51 PH2912051 CAP SCREW 52 PH2912052 SHAFT 53 PH2912053 LINER 54 PH2912054 SET SCREW 55 PH2912055 MAGAZINE 56A PH2912056A STAPLE GUIDE UNIT 57A PH2912057A END CORE ASBLY. 58 PH2912058 CAP SCREW 59 PH2912059 ROLLED PIN 60 PH2912060 PUSHER 61 PH2912061 SLIDE BLOCK 62 PH2912062 SPRING 63 PH2912063 ROD 64 PH2912064 SET BLOCK 65 PH2909065 TAIL COVER -11-H2912/H2913 2...
Questo manuale è adatto anche per i modelli :Chiodatrici - H2912 (666.95 kb)