valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
To increase depth of drive, first pull up on the upper WCE, then rotate thumbwheel to the left (counterclockwise). To decrease depth of drive, rotate thumbwheel to the right (clockwise). Then release upper WCE into detents which hold the thumbwheel in place after each adjustment. 3. Make sure that the trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. Movement ADJUSTING THE DIRECTION OF THE EXHAUST The IFN35650 is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. Rotate CLEARING A JAM FROM THE NAILER 1. Disconnect the air supply from the nailer. 2. Remove all nails from the magazine (see Loading/ Unloading). Failure to do so may cause the nails to eject from the front of the nailer. 3. Undo latch by pulling out and down. The wire latch will disengage from the hooks on the nose. 4. The door can now be rotated, exposing the jammed fastener. 5. Remove the jammed fastener, using pliers or a screwdriver if required. 6 Rotate door back into the closed position. 7. Extend the wire latch and place over the hooks on the nose. 8. Close the latch by pushing the latch up and in until the latch snaps into place. 9. Make sure the trigger and work contact element (WCE) move freely up and down Movement without sticking or binding. Technical Support Please call our Nailer Hotline at 1-800-543-6400 with any questions regarding the operation or repair of this nailer. Fastener And ReplacementParts !WARNING Use only 15 gauge 35° fasteners. Use only genuine Campbell Hausfeld replacement parts. Never substitute parts. Do not use modified parts or parts which will not give equivalent performance to the original equipment. Tool performance, safety and durability could be reduced. When ordering replacement parts or fasteners, specify by part number. Nailer Repair Nailer repairs must be performed by qualified and experienced service people ONLY. Assembly Procedure For Seals When repairing a nailer, the internal parts must be cleaned and lubricated. Parker O-lube or equivalent must be used on all o-rings. Each o-ring must be coated with O-lube before assembling. A small amount of oil must be used on all moving surfaces and pivots. After reassembling, a few drops of 30W non- detergent oil or equivalent, must be added through the air line before testing. Fasteners Information Nails used in the Campbell Hausfeld IFN35650 Angle Finish Nailer will also work in Sears 18329, Porter Cable DA250, Senco SFN2B, SFN1 and SFN40. 5 Operating Instructions Model IFN35650 Troubleshooting Guide !WARNING Stop using nailer immediately if any of the following problems occur. Serious personal injury could result. Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center. Problem Cause Solution Air leaking at trigger O-Rings in trigger valve housing are Replace O-Rings. Check operation of Work Contact valve damaged Element (WCE) Air leaking between housing and nose Loose screws in housing Damaged O-Rings Damage to bumper Tighten screws Replace O-Rings Replace bumper Air leaking between housing and cap Loose screws Damaged gasket Tighten screws Replace gasket Nailer skips driving nail Worn bumper Dirt in nose piece Replace bumper Clean drive channel Dirt or damage prevent nails or pusher from moving freely in magazine Clean magazine Damaged pusher spring Replace spring Inadequate air flow to nailer Check fitting, hose or compressor Worn O-Ring on piston or lack of lubrication Replace and lubricate O-Rings Damaged O-Ring on trigger valve Replace O-Rings Air leaks Tighten screws and fittings Cap gasket leaking Replace gasket Nailer runs slow or has loss of power Nailer not lubricated sufficiently Broken spring in cylinder cap Exhaust port in cap is blocked Lubricate nailer Replace spring Replace damaged internal parts Nails are jammed in Guide on driver is worn Replace guide nailer Nails are not correct size Use only recommended nails Nails are bent Replace with undamaged nails Magazine or nose screws are loose Tighten screws Driver is damaged Replace driver 6 Operating Instructions Model IFN35650 Limited Warranty 1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year. 2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison, Ohio, 45030, Telephone: (800) 543-6400 3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell Hausfeld product. 4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: Any Campbell Hausfeld nailer, stapler, air tool, spray gun, inflator or air accessory supplied or manufactured by Warrantor. 5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the duration of the warranty peri...