valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
4 5 Operating Instructions SN338K00 Operating Instructions (Continued) RECOMMENDED HOOKUP The illustration below shows the recommended hookup for the tool. 1. The air compressor must be able to maintain a minimum of 60 psi when the tool is being used. An inadequate air supply can cause a loss of power and inconsistent driving. 2. An oiler can be used to provide oil circulation through the tool. A filter can be used to remove liquid and solid impurities which can rust or “gum up” internal parts of the tool. 3. Always use air supply hoses with a minimum working pressure rating equal to or greater than the pressure from the power source if a regulator fails, or 150 psi, whichever is greater. Use 1/4 inch air hose for runs up to 50 feet. Use 3/8 inch or greater air hoses for 50 foot run or longer. 4. Use a pressure regulator on the compressor, with an operating pressure of 0 - 125 psi. A pressure regulator is required to control the operating pressure of the tool between 60 and 100 psi. OPERATIONAL MODE - SINGLE CYCLE Always know the operational mode of the tool before using. Failure to know the operational mode could result in death or serious personal injury. This tool requires the trigger to be pulled each time a nail is driven. The nailer can be actuated by depressing the WCE against the work surface followed by pulling the trigger. The trigger must be released to reset the tool before another nail can be driven. WORK CONTACT ELEMENT (WCE) Check the operation of the Work Contact Element (WCE) trip mechanism before each use. The WCE must move freely without binding through its entire travel distance. The WCE spring must return the WCE to its fully extended position after being depressed. Do not operate the nailer if the WCE trip mechanism is not operating properly. Personal injury may occur. 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine (see Loading/ Unloading). 3. Make sure the trigger and work contact element (WCE) move freely up and down without sticking or binding. 4. Reconnect air supply to the tool. 5. Depress the Work Contact Element (WCE) against the work surface without pulling the trigger. The tool MUST NOT OPERATE. Do not use the tool if it operates without pulling the trigger. Personal injury may result. 6. Remove the tool from the work surface. The Work Contact Element (WCE) must return to its original down position. The tool MUST NOT OPERATE. Do not use the tool if it operates while lifted from the work surface. Personal injury may result. 7. Pull the trigger and depress the work contact element (WCE) against the work surface. The tool MUST NOT OPERATE. 8. Depress the Work Contact Element (WCE) against the work surface. Pull the trigger. The tool MUST OPERATE. An improperly functioning tool must not be used. Do not actuate the tool unless the tool is placed fi rmly against the work piece. 150 psi or greater 60 psi Min. 100 psi Max. Minimum Recommended Hookup Quick Plug Quick Coupler Air Hose Quick Plug Quick Coupler 6 Operating Instructions SN338K00 Operating Instructions (Continued) LOADING/UNLOADING THE TOOL 1. Always disconnect the tool from the air supply before loading fasteners. 2. Push down on the latch button. Pull back on the magazine cover. 3. Load a clip of staples with the crowns straddling the magazine rail. 4. Push the magazine cover forward until latch button pops up. 5. Always unload all fasteners before removing tool from service. Unloading is the reverse of loading, except that you must disconnect the air supply before unloading. ADJUSTING THE FASTENER PENETRATION The tool is equipped with an adjustable depth of drive feature. This allows the user to determine how deep a fastener will be driven into the work surface. 1. Adjust operating pressure so nails are driven consistently. Do not exceed 100 psi. 2. To drive the nail shallower, turn the wheel (C) to right to the extent desired. 3. To sink a nail deeper, turn the wheel (C) to left to the extent desired. 4. Make sure trigger and work contact element (WCE) move freely up and down without binding or sticking after each adjustment. ADJUSTING THE DIRECTION OF THE EXHAUST The tool is equipped with an adjustable direction exhaust deflector. This is intended to allow the user to change the direction of the exhaust. Simply twist the deflector to any direction desired. User - Maintenance Instructions CLEARING A JAM FROM THE TOOL 1. Disconnect the air supply from the tool. 2. Remove all fasteners from the magazine (see Loading/ Unloading). Failure to do so will cause the nails to eject from the front of the tool. 3. Loosen cap screws on nose of tool. Slide nose downward and remove from tool to expose jammed fastener. 4. Reinstall nose assembly in reverse order in Step #3. 5. Make sure the trigger and Work Contact Element (WCE) move freely up and down without sticking or binding. TECHNICAL SERVICE Please call our Tool Hotline at 1-800- 543-6400 wit...
Questo manuale è adatto anche per i modelli :Chiodatrici - SN338K00 (559.64 kb)