valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
We believe your new Graco® highchair is a wise choice, promising many hours of enjoyment for your baby. Before using your highchair, please take a few minutes to read this Owner.s Manual. The short time you spend reading these instructions will help you use your highchair properly. Please save your Owner.s Manual for future use. Customer Satisfaction Our goal is to make every product the best it can be! We are also committed to supporting our products after purchase. If you would like to speak to Graco about your product, please contact our Customer Service Department at 1-800-345-4109. Our knowledgeable staff will be ready to answer any questions you may have concerning parts, use, or maintenance. When you call, please have the model and serial numbers ready so your call may be processed quickly and efficiently. OWNER.S MANUAL Model No. _______ Serial No. ________ Dear Customer, Please fill in the model and serial numbers above from the label on the back of the footrest of your new highchair. Models 3835, 3845, 3848, 3855, and 3865 Never leave child unattended. Always keep your child in view. Prevent serious injury or death from falls or sliding out. Always secure child in the restraint. THIS PRODUCT REQUIRES ADULT ASSEMBLY. FOLLOW ASSEMBLY INSTRUCTIONS CAREFULLY. If you experience any difficulties, please contact the Customer Service Department. THIS HIGHCHAIR IS DESIGNED TO BE USED by a child up to 3 years old. Maximum weight 37 pounds (17 kg). DO NOT FORCE TRAY against child. Use only the five adjustment positions. Be sure all adjustment fingers are in armrest slots. DISCONTINUE USING YOUR HIGHCHAIR should it become damaged or broken. Highchair 3 4 warnings and the assembly in serious injury or death. Seat with seat belt or harness Large tray Chair frame Screw (2) CARE AND MAINTENANCE FROM TIME TO TIME CHECK YOUR HIGHCHAIR for loose screws, worn parts or torn material. Replace or repair the parts as needed. Use only Graco® replacement parts. REMOVABLE CLOTH SEAT PAD (on certain models) may be machine washed in lukewarm water on delicate cycle and drip-dried. NO BLEACH. TO CLEAN HIGHCHAIR FRAME, use only household soap or detergent and warm water. NO BLEACH. Seat pad (style depends on model) Crossbrace tube Right plastic leg tube Left plastic leg tube Small tray Bolt (2) T-nut (2) Hex wrench Foot top (2) Foot bottom (2) Secure your child at all times with the restraint system provided, in either the reclining or upright position. The tray is not designed to hold your child in the highchair. It is recommended that the highchair be used in the upright position only by children capable of sitting upright unassisted. STRANGULATION HAZARD: DO NOT place highchair in any location where there are cords, such as window blind cords, drapes, phone cords, etc. Leg tube end cap (2) PARTS LIST CHECK that you have all the parts listed below BEFORE assembling your highchair. If any parts are missing, call Customer Service at 1-800-345-4109. Tool required: Screwdriver 225-12-98 IS3850 5 Step 1. IMPORTANT: BEFORE attaching feet to highchair, frame MUST be folded exactly as in the drawing below. Lay highchair frame on floor so it looks like the drawing before attaching feet. Place a foot top and foot bottom at each corner of the chair frame tube. Insert a screw into the foot bottom, through the hole in the chair frame, and into the foot top. Tighten screws securely, but do not overtighten. Step 2. Unfold the chair frame as shown. Insert one bolt and one T-nut into each leg brace and through the holes in the legs. Tighten them securely with a screwdriver and the enclosed hex wrench. Step 3. Snap end caps into ends of right and left plastic leg tubes. Step 4. Turn the seat upside down as shown. Match up the .L. or .R. on the plastic leg tubes with the letters molded on the seat back. Slide the leg tubes into the .collars. on the seat back. Slide the crossbrace tube through the slots under the seat. Then insert the ends of the crossbrace tube into the holes in the leg tubes. (This may be more easily done if the crossbrace tube is held at an angle as shown.) Step 5. Set chair frame into upright position. Slide the seat assembly onto the frame. Press the red latches, located on the plastic leg tubes, to allow seat to slide onto frame. NOTE: Lowest seat position should NOT rest on top of legs. Pull seat up to lowest latching position. To Attach Seat Pad SEAT PAD WITH FOUR TABS: Step 1. Place seat pad in seat. Large part of pad goes on seat back as shown. Pull the seat belt through the hole in the middle of the seat pad. Step 2. Push the four tabs on the seat cover into the slots at the top and bottom of the seat. Step 3. From the rear of the seat, pull the four tabs over the plastic anchors near them. 6 To Assemble Highchair Hex wrench Left plastic leg tube Collars Crossbrace tube Right plastic leg tube Lowest latching position NOT resting on legs Anchor Seat back Seat bottom Your highchair seat pad will either have 4 attachment...