valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
Please read these instructions before assembly and use of this product. Adult assembly is required. Tool needed for assembly: Phillips Screwdriver (not included). Warning and Caution WARNING Prevent serious injury or death from falls or sliding out: • The child should at all times wear a safety harness correctly fitted and adjusted. The tray is not designed to hold the child in the chair. • Always keep child in view while in the high chair. • Never leave child unattended. • It is recommended that the high chair be used in the upright position only by children capable of sitting upright unassisted. CAUTION This product contains small parts in its unassembled state. Adult assembly is required. 2 33 Parts Pad 3 Food Trays 2 Toys (Toys may be different) Seat Back Seat Bottom Frame Hinge Rod 2 Seat Bottom Tubes 4 Screw Retainers Base Tray Frame Footrest Headrest Basket Storage Caddy Front Base Back Base #10 x 2.2 cm Black Screw #10 x 2.2 cm Black Screw #10 x 2.2 cm Black Screw - 7 Shown Actual Size #8 x 1.9 cm Screw - 8 Tighten and loosen all screws with a Phillips screwdriver. Do not over-tighten the screws. #8 x 1.9 cm Screws #8 x 1.9 cm Screws #10 x 2.2 cm Black Screw 4 2 • Slide a seat bottom tube through each set of plastic rings on the seat bottom. 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. Assembly Plastic Rings Footrest Seat Bottom IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Seat Bottom Tubes Plastic Rings 3 Seat Bottom Tubes Plastic Rings Plastic Rings #8 x 1.9 cm Screw - 4 • Align the holes in the plastic rings and the seat bottom tubes. • Insert a #8 x 1.9 cm screw through each plastic ring and into the seat bottom tubes, as shown. Tighten the screws. • Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly. Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws. 4 2 • Slide a seat bottom tube through each set of plastic rings on the seat bottom. 1 • Place the seat bottom face down on a flat surface. • At an angle, fit the footrest on the seat bottom, as shown. Assembly Plastic Rings Footrest Seat Bottom IMPORTANT! Before each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replace- ment parts and instructions if needed. Never substitute parts. Seat Bottom Tubes Plastic Rings 3 Seat Bottom Tubes Plastic Rings Plastic Rings #8 x 1.9 cm Screw - 4 • Align the holes in the plastic rings and the seat bottom tubes. • Insert a #8 x 1.9 cm screw through each plastic ring and into the seat bottom tubes, as shown. Tighten the screws. • Push the seat bottom tubes back and forth to be sure they are secured to the seat bottom. If the seat bottom tubes move, you have probably not fastened them properly. Remove the screws and check to be sure the screw holes in the seat bottom tubes and seat bottom plastic rings are aligned. Replace and tighten the screws. 5 Assembly 4 Insert Screws Here Footrest • Insert two #10 x 2.2 cm black screws through the footrest and into the seat bottom. Tighten the screws. #10 x 2.2 cm Black Screw - 2 5 • Turn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly. Seat Back Pin Opening Seat Bottom Assembly Opening Seat Back Pin 6 Hinge Rod Hinge • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 9. #10 x 2.2 cm Black Screw 7 • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. Frame Leg 5 Assembly 4 Insert Screws Here Footrest • Insert two #10 x 2.2 cm black screws through the footrest and into the seat bottom. Tighten the screws. #10 x 2.2 cm Black Screw - 2 5 • Turn the seat bottom assembly upright. • Fit the seat back pins into the openings in the top side of the seat bottom assembly. Seat Back Pin Opening Seat Bottom Assembly Opening Seat Back Pin 6 Hinge Rod Hinge • Turn the seat assembly face down. • Insert the hinge rod through the hinge on the seat back and seat bottom, as shown. • Insert a #10 x 2.2 cm black screw into the hinge rod. Tighten the screw. • Set the seat assembly aside for Assembly step 9. #10 x 2.2 cm Black Screw 7 • Pull the frame leg out on each frame to open. Make sure it "clicks" into place. Frame Leg 6 Assembly 8 • Identify the back and front base. The front base ha...