valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
The filter may be Washed or vacuumed. Remove the excess water from the filter by Gently shaking the filter. This will remove dust and particles trapped in The filter. Lint build-up in screen restricts airflow, which causes longer Drying times. After cleaning, slide the filter back in place. DO NOT USE YOUR DRYER WITHOUT THE LINT FILTER. lint filter Donotuseanytypeofspray cleanerwhencleaning theinterior . Hazardous fumesor Electric shock could occur If dryer drum becomes stained,clean the drumwith a dampcloth.Removeany residue before drying the next load. Cleancabinetwith mild soap andwater.Donotuse harshor abrasive cleaners,this could damage the dryer. Clean the duct and theventon a regular basis to avoid clogging which could affect the efficiency of the dryer. Troubleshooting Dryer does not operate: Check if unit is plugged in. The plug may have come loose. Check if the electrical wall socket is the correct voltage. Check if the circuit breaker needs to be reset or if the fuse needs to be replaced. Check if the unit is in Off mode. Press Power On/Off button again. Check if door is open or not in place. Open and close the door slightly and make sure in place. Dryer is working but not drying the clothes: Unit may be over loaded. The dryer drum should only be half full. Check exhause ducts and vent. Vent should be free of all obstructions. Duct should be lint and dust free. Ducts should be cleaned regularly. Dryer load needs to be resorted. Heavy clothes may need to be separated from regular clothes. Bulky clothes may require repositioning. If clothes dry unevenly a higher dry setting may be required or clothes in the dryer may need to be resorted. Dryer making noise when drying: Coins, loose change, buttons and other heavy objects could make noise. Dryer may need to be leveled properly. Read OPERATING INSTRUCTION-Normal Operating Sounds. Static: Caused by over drying. Adjust for shorter drying time. Mixed with synthetic fabric. Sort and separate different fabrics. Use a fabric softener. INSTALLATION INSTRUCTIONS Select a suitable location for the dryer on a hard even surface away from direct sunlight or heat source e.g. radiators, baseboard heaters, cooking appliances etc. Any floor unevenness should be corrected with the leveling legs located on the bottom of the dryer. Tools and Materials Required Phillips head and flathead screwdrivers Channel-lock adjustable pliers 1/2 inch open end wrench Spirit level Measuring tape (12ft. Min.) Duct tape Rigid or flexible metal 4 inch (10.2 cm) duct Vent hood Electrical Requirements Power Supply: 3 wire, 220V Volt, 30 Amp, 50Hz, 1 Phase Power Supply Cord Kit:(not supplied when sold) The dryer MUST employ a 3-conductor power supply cord NEMA(245IEC66 450V/750V) rated at 220 Volt AC minimum, 30 Amp., with 3 open end spade lug connectors with upturned ends or closed loop connectors and marked for use with clothes dryers. Unpacking Your Dryer 1. Remove all packaging material. This includes the foam base and all adhesive tape holding the dryer accessories inside and outside. 2. Inspect and remove any remains of packaging, tape or printed materials before using the dryer. Exhaust System Connections Requirements and Instructions 1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up inside system and create a fire hazard and restrict air flow. Restricted air exhaust flow will increase dryer times. If your present system is made up of plastic duct or metal foil duct, replace it with a rigid or flexible metal duct. Ensure present duct is free of any lint prior to installing dryer duct. 2. If the dryer is not exhausted out doors, some fine lint will be expelled into the laundry area. An accumulation of lint in any area of the home can create a health and fire hazard. To reduce risk of fire, dryer MUST BE EXHAUSTED OUTDOORS. 3. Do not allow combustible material (for example: clothing, draperies/curtains, paper) to come in contact with venting system. The dryer must not be exhausted into a chimney, a wall, a ceiling, or any concealed space of a building which can accumulate lint, resulting in a fire hazard. 4. Exceeding the length of duct pipe or number of elbows allowed in the "Maximum Length" charts can cause an accumulation o...
Questo manuale è adatto anche per i modelli :essiccatori - GDZ22-2 (359.64 kb)
essiccatori - GDZ22-2 (359.64 kb)
essiccatori - GDZ22-2 (359.64 kb)
essiccatori - GDZ22-2 (359.64 kb)