valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
8 Control Instructions .............................................................................. 9 Dual Digital Timer Control.............................................................. 9 Single Drop Control......................................................................... 11 Ignition Control Operation ................................................................... 13 Maintenance ........................................................................................ 15 Daily ..................................................................................................... 15 Monthly................................................................................................. 17 Quarterly............................................................................................... 17 Bi-Annually .......................................................................................... 17 Before You Call for Service ............................................................... 20 Customer Service.................................................................................. 20 © Copyright 2007, Alliance Laundry Systems LLC All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Model Identification Information in this manual is applicable to these models: Gas Steam Electric CHD30STG2-CAT30L CHD30STS2-CTT30S CHD30STE2-CTT30E CHD30STG2-CAT30N CHD30STS2-CUT30S CHD30STE2-CUT30E CHD30STG2-CTT30L DRST30S2-BTT30S DRST30E2-BTT30E CHD30STG2-CTT30N DRST30S2-BUT30S DRST30E2-BUT30E CHD30STG2-CUT30L IPD30STS2-ITT30S IPD30STE2-ITT30E CHD30STG2-CUT30N T30 DRST30G2-BAT30L DRST30G2-BAT30N DRST30G2-BTT30L DRST30G2-BTT30N DRST30G2-BUT30L DRST30G2-BUT30N IPD30STG2-ITT30L IPD30STG2-ITT30N T45 IPD45STG2-ITT45L IPD45STG2-ITT45N Not Applicable Not Applicable Includes models with control suffixes: 3O – DX4 OPL QT – dual digital timer 3V – DX4 vended SD – single drop 3X – DX4 prep for coin SX – single drop, prep for coin © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Introduction Customer Service If literature or replacement parts are required, contact the source from which the machine was purchased or contact Alliance Laundry Systems at (920) 748-3950 for the name and address of the nearest authorized parts distributor. For technical assistance, call (920) 748-3121. Serial Plate Location When calling or writing for information about your product, be sure to mention model and serial numbers. Model and serial numbers are found on serial plate on the rear of machine and inside door. Refer to Figure 1. Wiring Diagram The wiring diagram is located in the upper junction or upper contactor box. The wiring diagram part number is located in the lower portion of the electrical data on the serial plate. TMB1974N 1 Serial Plate 1 Figure 1 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT Safety Information Explanation of Safety Messages Precautionary statements (“DANGER,” “WARNING,” and “CAUTION”), followed by specific instructions, are found in this manual and on machine decals. These precautions are intended for the personal safety of the operator, user, servicer, and those maintaining the machine. DANGER Indicates an imminently hazardous situation that, if not avoided, will cause severe personal injury or death. WARNING Indicates a hazardous situation that, if not avoided, could cause severe personal injury or death. CAUTION Indicates a hazardous situation that, if not avoided, may cause minor or moderate personal injury or property damage. Additional precautionary statements (“IMPORTANT” and “NOTE”) are followed by specific instructions. IMPORTANT: The word “IMPORTANT” is used to inform the reader of specific procedures where minor machine damage will occur if the procedure is not followed. NOTE: The word “NOTE” is used to communicate installation, operation, maintenance or servicing information that is important but not hazard related. IMPORTANT: Warranty is void unless tumbler is installed according to instructions in the Installation Manual. Compliance with minimum specifications and requirements detailed herein, and with applicable local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, and any other relevant statutory regulations. Because of varied requirements, applicable local codes should be thoroughly understood and all pre-installation work arranged for accordingly. WARNING Failure to install, maintain, and/or operate this machine according to manufacturer’s instructions may result in conditions which can produce serious injury, death and/or property damage. W051R1 NOTE: The WARNING and IMPORTANT instructions appearing in this manual are not meant to cover all possible conditions and situations that may occur....