valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
Otherwise your dryer might suffer damage. In addition energy consumption will be increased if the heat exchanger unit is covered with fluff. See the section "Drying, cleaning the heat exchanger". Programming possibilities The electronic control system of your laundry dryer provides you with the possibility to adapt some functions of the dryer permanently to your requirements. Purpose Execution "Laundry protection": If you want to "lock" the selected drying programme (the selected programme setting cannot be changed during the drying process with the programme selector or with the SPECIAL CARE or QUICK button): When "Washing Protection" is enabled, the drying programme always runs at reduced heater power (SPECIAL CARE Function). If you always want to be reminded by an audible signal at the end of the programme: If you remove condensation via an external condensation drain off and wish to permanently suppress the EMPTY WATER indication: When a drying programme is set with the programme selector and the START button has been pressed: - Hold the SPECIAL CARE button depressed for five seconds. The programme execution display flashes for five seconds and the laundry protection is then switched on. If an attempt is nevertheless made to change the programme setting, the programme execution display flashes; after pressing the SPECIAL CARE or QUICK button, it flashes for five seconds; on turning the programme selector it flashes until the programme selector is returned to the initial setting. To cancel the laundry protection: - Hold the SPECIAL CARE button depressed for five seconds. The programme run indicator flashes for five seconds, then it is static for five seconds; laundry protection is cancelled. 1) Ensure that the programme selector is not in the LIGHT or OFF position. 2) Hold the AUDIBLE SIGNAL button depressed for at least five seconds. The AUDIBLE SIGNAL display lights; a short audible signal is heard. The audible signal is now programmed. If you want to cancel this setting: 3) Proceed as described under item 1) and 2). The display AUDIBLE SIGNAL disappears. 1) Set the programme selector to LIGHT. 2) Hold the AUDIBLE SIGNAL button depressed for five seconds. The PROGR. TIME display shows U for normal function and & for external condensation drain off. 3) Briefly press the AUDIBLE SIGNAL button to choose between U and & . 4) Turn the programme selector. The EMPTY WATER indicator is now suppressed. Programming possibilities Purpose Execution Adjusting the drying result: If at the end of the programme you always want the washing to be somewhat drier or somewhat damper than with the standard setting and you want to adjust the tumble dryer’s recognition of the degree of dryness accordingly: 1) Turn the programme selector to the LIGHT position. 2) Hold down the DELAY TIMER button for five seconds. The current setting appears in the PROGR. TIME display: H1 is the standard setting, with H0 the washing will be drier, with H2 the washing will stay damper. 3) Keep pressing the DELAY TIMER button until the value you require appears in the display. 4) Turn the programme selector. The selected setting is then saved. What to do if ... If the tumble dryer is not working correctly please carry out the following checks before calling out an engineer. Symptom Possible cause Solution The tumble dryer will not start The results are unsatisfactory The appliance is not plugged in Plug in the appliance The fuse has blown Check the fuse The START/PAUSEbutton has not been pressed Press the START/PAUSE button No programme has been selected Select the required programme The door is not properly closed Close the door The water reservoir is full Empty the water reservoir The wrong programme has been selected Select a different programme Fluff filter blocked Clean the fluff filter Heat exchanger unit covered with fluff Clean the heat exchanger unit The tumble dryer has been overloaded Observe the maximum loads stated for each programme Laundry not sufficiently spun prior to tumble drying Ensure the wash load is well spun before tumble drying The vent in the base of the appliance is covered Ensure the vent is clear A residue may have formed on the drum interior, blocking the sensors Clean the inside of the drum with white vinegar What to do if ... Symptom Possible cause Solution Reprogramme the stand- The conductivity of the The drying result is unsatis ard setting, eg. H0 instead water in your locality dif factory; the washing is still of H1, for dryer washing fers from the standard damp. (see chapter “Program- setting of the appliance. ming Possibilities“. The drum illumination does not work Is the tumble dryer Plug in the tumble dryer plugged in The programme selector Turn the programme is in the OFF position selector dial to LIGHT The bulb needs replacing Replace bulb The heat exchanger unit Clean the heat exchanger The drying process takes is covered with fluff unit unusually long Fluff filter is clogged Clean the fluff filter The ...