valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
The signal will beep and the status lights will flash, but the original cycle will continue. Auto Dry Auto Dry cycles take the guesswork out of drying time. Loads dried using the Towels, Normal, Perm Press and Delicate cycles will dry automatically at the selected temperature to the desired dryness level. The dryer uses sensing bars to sense the moisture level of the load as it tumbles through heated air. Auto Dry cycles save time and energy and protects fabrics. The estimated drying time will be displayed for about 5 minutes. Then the outside of the display will light up in a circular track to indicate the drying time is automatically being determined by the sensors. When the load has reached the selected dryness level, it will continue to tumble, unheated, during a Cool Down period. This helps reduce wrinkling and makes items easier to handle during unloading. The estimated Cool Down time will be displayed. Drying time varies depending on size and dampness of load and fabric type. If the load is too small or almost dry, the sensing bars may not detect enough moisture to continue the cycle and the cycle may end after a few minutes. Select a Timed Dry setting to dry such loads. Room temperature and humidity, type of installation and electrical voltage or gas pressure can also affect drying time. Towels Select this Auto Dry cycle for towel loads. Normal Select this Auto Dry cycle for cotton items. Perm Press Select this Auto Dry cycle for cottons and blends with a no-iron finish. Delicate Select this Auto Dry cycle for knits and delicate items. Quick Select this cycle to quickly dry a small load made up of just a few items. It provides approximately 20 minutes of tumbling followed by a 10-minute cool down period. Bulky Select this cycle to dry a comforter, blanket, sleeping bag or similar item.Cool Down is approximately 10 minutes. Timed Dry To manually select the drying time for any load, turn the knob to a numbered setting. Drying times from 15 to 90 minutes are available in 15-minute increments. You will not be able to select a cycle or dryness level. Timed Dry is recommended when using the No Heat option. Note: To change cycles, press Pause/Cancel twice. To avoid fire hazard, do not use heat to dry itemscontaining feathers or down, foam rubber, plastic, or similarly textured, rubber-like materials. Use the No Heat setting only. 137102600 (0806) Cycle Selection (Con’t) Drying Temperature For best results, follow the fabric care label instructions on items to be dried. To change the drying temperature, press TEMP to scroll to the desired heat. To protect your wardrobe, not all temperatures are available with every cycle. High heat is recommended for sturdy fabrics. Medium High heat is recommended for most cotton fabrics. Medium heat is recommended for wrinkle free, permanent press and lightweight fabrics. To increase drying time for similar loads in the future, select More Dry. For loads requiring less drying time, select Less Dry. Select Damp Dry for items you wish to partially dry before hanging or ironing. Note: To prevent over-drying, not every dryness level is available with every cycle. Options To select an option, press OPTIONS until the indicator for the desired option flashes, then press Select. If an option is not available for a cycle, the indicator will not light. Follow the same steps to delete an option. Low heat is recommended for delicate fabrics. No Heat should only be used with a Timed Dry setting to dry items containing feathers, down, foam rubber, plastics or rubber- like materials; to freshen clothing, pillows or blankets; or to dust draperies. Note: Using No Heat in any Auto Dry cycle will result in long drying times and /or wet loads at the end of the cycle. Cycle Settings Appropriate drying temperature, dryness level and options will automatically be indicated for each cycle. The TEMP, DRYNESS and OPTIONS settings can be changed before the cycle is started. Those adjustments will automatically be remembered each time that cycle is selected. If a temperature, dryness level or option is not recommended for a cycle, the indicator will not light. If changes are attempted after the cycle starts, the status lights will blink, the signal will beep and “Err” will be displayed. To change a setting after the cycle starts, press Pause/Cancel once, adjust the setting and press START to resume the cycle. See the “Dryer Settings Chart” for more details. Dryness Level To change the dryness level, press DRYNESS until the desired selection is made. Select Normal for most loads. Occasionally a load may seem too damp or over-dried at the end of the cycle. The Cycle Signal will sound at the end of the cycle and periodi cally during Press Saver. Select Shrink Guard to lower the initial drying temperature to protect fabrics from overdrying. Select Press Saver if the dried load might not be removed promptly at the end of the cycle. The dry load will continue to tumbling without heat for 30 minutes to help...