valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Press the START PAUSE button sequentially until you set desired level. 4. To memorize setting press simultaneously the DELI- CATE and TIME buttons or turn knob to OFF position Emptying water tank - warning mes- sage permanent off When using an external drain for the condensed water. 1. Turn the programme selector to any programme. 2. Press simultaneously the LONG ANTI-CREASE and TIME buttons and hold down for approx. 5 seconds. The current setting is on the display: – - led warning is permanently off – - led warning is activated By default the warning led is activated and is lighting always at the end of the drying cycle or during the cycle if the water container is full. Technical data 23 Technical data This appliance conforms with the following EU Directives: – 2006/95/EEC dated 12.12.2006 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x width x depth 85 x 60 x 58 cm Depth with loading door open 109 cm Height can be adjusted by 1.5 cm Weight when empty approx. 40 kg Loading volume (depends on programme)1) max. 7 kg Energy consumption in accordance with EN 61121 s. e. (7kg of cotton, pre-drained at 1000 rpm, COTTONS STORAGE DRY programme) 4,4 kWh Use Domestic Permissible ambient temperature + 5°C to + 35°C 1) Different loading volume data may be needed in some countries as a result of different measuring methods. Consumption values The consumption values have been established under standard conditions. They may deviate when the machine is operated in domestic circumstances. Programme Loading volume in kg Energy consumption in kWh COTTONS CUPBOARD DRY1) 7 4.4 COTTONS IRON DRY1) 7 3.41 SYNTHETICS CUPBOARD DRY2) 3 1.36 1) pre-drained at 1000 rpm 2) pre-drained at 1200 rpm Hints for test institutes Parameters possible to check by the Test Institutes: • Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with nominal load. • Energy consumption (corrected with final humidity) during the cupboard dry cotton cycle with half load. • Final humidity (during cupboard dry cotton, iron dry cotton and cupboard dry easy care) • Condensation efficiency (corrected with final humidity) during cupboard dry cotton cycle with nominal and half load All the cycles have to be checked in accordance with EN 61121 (Tumble dryers for household use – Methods for measuring the performance). Installation Appliance positioning • It is recommended that, for your convenience, the machine is positioned close to your washing machine. • The tumble dryer must be installed in a clean place, where dirt does not build up. • Air must be able to circulate freely all round the appliance. Do not obstruct the front ventilation grille or the air intake grilles at the back of the machine. • To keep vibration and noise to a minimum when the dryer is in use, it should be placed on a firm, level surface. • Once in its permanent operating position, check that the dryer is absolutely level with the aid of a spirit level. If it is not, raise or lower the feet until it is. • The feet must never be removed. Do not restrict the floor clearance through deeppile carpets, strips of wood or similar. This might cause heat built-up which would interfere with the operation of the appliance. The hot air emitted by the tumble dryer can reach temperatures of up to 60°C. The appliance must therefore not be installed on floors which are not resistant to high temperatures. When operating the tumble dryer, the room temperature must not be lower than +5°C and higher than +35°C, as it may affect the performance of the appliance. WARNING! Should the appliance be moved, it must be transported vertically. WARNING! The appliance must not be installed behind the lockable door, a sliding door or a door with a hinge on the opposite side to that of the appliance. Removing transport safety packaging CAUTION! Before use all parts of the transport packaging must be removed. 1. Open loading door 2. Pull off adhesive strips from inside machine on top of drum. 24 Installation Installation 25 3. Remove foil hose and polystyrene padding from the machine. Electrical connection Details on mains voltage, type of current and the fuses required should be taken from the rating plate. The rating plate is fitted near the loading aperture (see “Product description” chapter). Connect the machine to an earthed socket, in accordance with current wiring regulations. WARNING! The manufacturer declines any responsibility for damage or injury through failure to comply with the above safety precautions. Should the appliance power supply cable need to be replaced, this must be carried out by our Service Centre. The appliance is supplied with a 13 amp plug fitted. In the event of having to change the fuse in the plug supplied, a 13 amp ASTA approved BS 1363/A fuse must be used. The wires in the mains lead are coloured in accordance with the following code: Blue ...
Questo manuale è adatto anche per i modelli :essiccatori - 56740 (1.71 mb)
essiccatori - 56740 (1.71 mb)
essiccatori - 56740 (1.71 mb)