valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
Option 1: 4-wire connection with a Power supply cord. 18 1. Connect neutral wire(white) of power cord to center terminal block screw. 2. Connect ground wire of appliance and neutral wire of power cord to center terminal block screw. 3. Connect red and black wire to the left and right terminal block screws. 4. Make sure that the strain relief screw is tightened. and be sure that all terminal block nuts are on tight and power cord is in right position. 5. Connect a independent ground wire from external ground connector to proper ground. Part 5 ELECTRICAL REQUIREMENTS FOR ELECTRIC DRYERS lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under Section 3: Optional 3-wire connection. Option 2: 3-Wire Connection with a Power Supply Cord • If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under this section. Option 3: Optional 3-wire connection. Part 6 ELECTRICAL REQUIREMENTS FOR GAS DRYERS 120 Volt, 60 Hertz, with 3-Prong Grounding Plug Following are additional instructions regarding electrical connections and requirements for gas dryers. ! Important Warning: To help prevent fire, electric shock, serious injury or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1, and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer. Electrical Requirements for Your Dryer: a) Please note that the wiring diagram is provided inside the dryer control hood. Label all wires prior to disconnection when servicing the dryer, because wiring errors can cause serious injury to you and your dryer. b) Your dryer is designed to be used on a separate branch, polarized, three-wire, effectively grounded, 120 Volt, 60 Hertz, AC (alternating current) circuit protected by a 15 Ampere fuse, equivalent fusetron or circuit breaker. c) Use separately fused circuits for washers and dryers, and DO NOT operate a washer and a dryer on the same circuit. STANDARD 120 VOLT, 60 HERTZ, 3-WIRE EFFECTIVELY GROUNDED CIRCUIT 1 L1 WARNING! 2 Ground 3 Neutral Side Do not overload the circuit by operating 4 Round Grounding Prong other appliances on the same circuit when 5 Neutral this appliance is operating, by using an extension cord to connect the dryer to the a) The dryer has a three-prong plug to help guard power source, or by using any adapter to against shock. The plug should be plugged allow additional cords to connect to the directed into a properly grounded three-prong same outlet. receptacle that is rated 120 Volts AC (alternating current) 15 Amps. This plug, in order to be properly and fully effective, must be plugged into a properly installed outlet that is grounded in accordance with all local codes and ordinances. ! WARNING! b) The dryer must be grounded in order to reduce the risk of electric shock, including a malfunction or breakdown. DO NOT modify the plug provided with the dryer. If it does not fit the outlet in your c) If your laundry room does not meet the laundry room, a proper outlet will need to be specifications required by this manual, or if you installed in your laundry room by a qualified are uncertain whether or not your laundry room service person or company. meets these specifications, please have a qualified service person or company, for example a qualified electrician or your local electric company, review your laundry room’s electrical supply for any problems. ! Part 7 GAS REQUIREMENTS AND INSTRUCTIONS Following are important instructions and information concerning the requirements for the gas supply and service for gas dryers. ! Important Warning: The gas supply and service for a gas dryer must comply with all local codes and ordinances. In the absence of any local codes or ordinances in your area, the gas supply and service for your gas dryer must comply with the latest edition of the National Fuel Gas Code, ANSI Z223.1/NFPA 54. 1. Gas supply requirements: Liquefied Petroleum (L.P.) Gas (2,500 Btu/ft3 (93.1 MJ/m3)) service must be provided at 10 + 1.5 in. water column pressure. 2. Important: DO NOT connect the dryer to the Liquefied Petroleum (LP) Gas service without converting the gas value. 3. A qualified technician must perform the LP Gas conversion. Contact your local gas service branch if you require additional assistance or information. 4. Isolate the dryer from the gas supply piping system by closing its individual manual shut-off valve, during any pressure testing of the gas supply system at test pressure equal to or less than 2/1 psi (3.45 kPa). 5. Supply Line Requirements. Your laundry r...
Questo manuale è adatto anche per i modelli :essiccatori - DLE2512W (5.35 mb)