valutazioni - 3, GPA: 3.7
(
)
)
|
Foto e specifiche Miele T 8822 C |
Facilità d'uso
. Turn the lever down to the horizontal position, making sure that the hook on the lever clicks into the groove. When replacing the inner cover after cleaning, ensure that the rubber seal fits correctly into the groove. . Replace the inner cover making sure the hooks locate correctly. Hold it at an angle and push it gently downwards. . Then turn the lever upwards into the horizontal position to lock the cover. . Replace the service panel and press the upper edge until it clicks into position. It is important to ensure that both the condenser unit and the cover are correctly positioned and locked, otherwise water may leak from the dryer. Problem solving guide With the help of the following notes, minor faults in the performance of the appliance, some of which may result from incorrect operation, can be put right without contacting the Service Department. Repair work to electrical appliances should only be carried out by a suitably qualified person in strict accordance with current local and national safety regulations. Repairs and other work by unqualified persons could be dangerous. The manufacturer cannot be held liable for unauthorised work. Check and fault messages Problem Possible cause Remedy The programme stops and 0 and Finish appear in the display. The buzzer sounds. This is not a fault. The electronic unit has recognised that there is no laundry in the drum and cancelled the programme. Drying individual garments or items which are already dry can also cause the programme to be cancelled. – Use the Warm air programme (timed drying) to dry individual items. – To select a new programme, switch the dryer off and on, or – Open the door, place more laundry in the drum, then close the door. The Low temperature indicator light starts flashing after the dryer has been switched on and 0-§ appears in the display. The electronic system lock is activated. You will need to deactivate the system lock before the dryer can be used (see "Electronic system lock"). The programme stops and Cooling down or Finish flashes in the display. The buzzer sounds. No obvious cause. – Switch the dryer off and then on again. – Then start the programme again. If the programme stops again and Cooling down or Finish flashes again, there is a fault. Contact the Miele Service Department. Problem solving guide Problem Possible cause Remedy The Clean out airways indicator light comes on. This indicator light comes on to warn you that the dryer is not working efficiently. Possible cause: the fluff filters are clogged with fluff or with detergent residues. – Cleaning the fluff filters is usually all that is required. However, if the Clean out airways indicator light does not go out after you have cleaned the filters, then also check all the possible causes described under "The drying process goes on too long or even switches off". To switch off the indicator light: – Open and close the door. The Clean out airways indicator light can be deactivated (see "Programmable functions"). The programme stops. The Clean out airways indicator light comes on. The buzzer sounds. See above for possible causes and their remedies. To switch off the indicator light: – Open and close the door. – Then start the programme again. – If the Clean out airways indicator light comes on again, contact the Miele Service Dept. The Empty container indicator light comes on. The buzzer sounds. The condensed water container is full or there is kink in the drain hose. – Empty out the condensed water container. – Check the drain hose. To switch off the indicator light: – Open and close the door. Problem solving guide Problem Possible cause Remedy The Denim, Shirts and Cool air programmes will not start and the indicators for these programmes do not light up. No obvious cause. – Switch the dryer off and then on again. – Select one of the programmes. – If the programme will still not start, there is a fault. Contact the Miele Service Department. – Use another programme in the meantime. The Start/Stop button The flashing indicates After the programme has flashes/does not flash. that a programme can be started. started, the flashing will change to a constant light. Problem solving guide An unsatisfactory drying result Problem Possible cause Remedy The laundry is not sufficiently dry. The load consisted of different fabrics. – Finish drying using the Warm air programme. – Select a different programme next time *. Items made of synthetic fibres are charged with static electricity after drying. Synthetic fibres tend to attract static charge. Static charge can be reduced by adding a fabric conditioner to the final rinse in the washing programme or a fabric conditioner sheet to the load when drying. There is a build-up of fluff. Fluff is principally the result of friction when garments are being worn and to some extent when they are being washed. Machine drying hardly causes any fluff to form and has no appreciable effect on the lifetime of the fabric. Fluff is collected by the fluff...